Husqvarna GT48XLSi To Replace Motion Drive Belt See Fig, To Remove Wheel See Fig, Belt Removal

Page 25

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 44)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower. (See “TO REMOVE MOWER” section in this manual.)

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Removebeltfromstationaryidler(C)andclutchingidler(D).

5.Remove belt from centerspan idler (E).

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

7.Remove belt downward from engine pulley and around electric clutch (G).

8.Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pul- ley (F). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (E).

5.Installbeltthroughstationaryidler(C)andclutchingidler(D).

6.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

7.Reconnect clutch harness (A).

8.Ensure belt is in all pulley grooves and inside all belt guides and keepers.

9.Install mower. (See “TO INSTALL MOWER” section in this manual.)

		G
B		H
	A	H
	A
		C
		J
		D
		E
		F

Fig. 44

TO REMOVE WHEEL (See Fig. 45)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING RING	WASHERS

AXLE

COVER

SQUARE KEY (REAR WHEEL ONLY)

Fig. 45

25

Image 25

Contents English/Spanish Operator’s Manual Manual de OperarioSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigTo Operate Mower To Adjust Gauge Wheels See FigTo Stop Mower Blades Reverse Operation System ROS See FigBattery Indicator Button See Fig Battery INDICATOR/CHARGING Plug See FigTo Transport See Fig Before Starting the Engine Resetting Ignition System Passcode See FigCheck Engine OIL Level ADD GasolineTo Start Engine Smartswitch Warning Lights See FigPRE-START StartingPurge Transmission Mowing TipsHour Meter Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Cleaning Deck Washout Port See Fig To Install Mower See Service and AdjustmentsTo Remove Mower See Fig O PSecure with small washer and small retainer spring as shown Mower, or, counterclockwise Loosen to lower Front mower To Level MowerTo Check Brake To Replace Mower Blade Drive BeltFront Wheel TOE-IN/CAMBER PulleysTo Replace Motion Drive Belt See Fig Belt InstallationTo Remove Wheel See Fig Belt RemovalReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Replace LED Headlight Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig Smartswitch Ignition System Lights See FigREMOVAL/REPLACEMENT To Adjust Throttle Control CableOther StorageFuel System Engine OILProblem Cause Correction TroubleshootingBattery will not To run when operFires when turn Engine continuesConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationAdvertencia Reglas DE SeguridadFuncionamiento General II. Funcionamiento EN PendientesIV. Remolque III. NiñosServicio Manipulación Segura DE LA GasolinaEspecificaciones DEL Producto Tabla DE MateriasResponsabilidades DEL Cliente Montaje Piezas SIN MontarHerramientas Necesarias Para EL Montaje Para Remover EL Tractor DE LA Caja DE CartónRevisión DE LA Nivelación DEL Conjunto Revisión DE LA Presión DE LAS LlantasRevisión DE LA Posición Adecuada DE Todas LAS Correas Revisión DEL Sistema DE FrenosOperación Amperímetro Indica la carga + o la descarga de la batería Familiaricese CON SU TractorPara Ajustar EL Freno DE Estacionamiento Vea Fig Como Usar SU TractorParada Vea Fig Cómo Usar EL Control DEL Cierre Diferencial Para Operar LA Segadora Para Ajustar LAS Ruedas Calibradoras Vea FigPara Parar LAS Cuchillas DE LA Segadora Sistema DE Operación EN Reversa ROS Vea FigRemolquedecarretillasootrosaccesorios Para Transportar Vea FigFaros Delanteros Testigo DE BATERÍA/CONECTOR DE Carga Vea FigRevise EL Nivel DE Aceite DEL Motor Antesde Hacerarrancar EL MotorAgregue Gasolina Para Operar DE LA Valvula DE Gasolina DE Reserva Vea FigArranque DEL Motor Purgar LA Transmisión Consejos Para SegarContador Horario Recomendaciones Generales MantenimientoTabla DE Lubricación Antes DE Cada USOOperación DEL Freno TractorCuidado DE LA Cuchilla LlantasMotor Limpieza Puerto DE Lavado DE LA Cubierta Vea Fig Instale LA Segadora Vea Servicio Y AjustesBarra Antibalanceo S Instale la correa pasándola por encima de la polea del motor Para Nivelar LA Segadora Impresión / Inclinación DE LAS Ruedas DEL- Anteras Controlar Y Ajustar EL FrenoDesmontaje DE LA Correa Para Cambiar LA Correa DE Impulsión DE Movimiento Vea FigMontaje DE LA Correa Para Remover LAS Ruedas Vea FigReemplazar LA Bateria Vea Fig Para Hacer Arrancar EL Motor CON UNA BAT- Ería Baja Vea FigSustitución DEL Faro LED Entrecierre Y ReléTransmisión Luces DEL Sistema DE Arranque Smartswitch Vea FigPara Remover EL Conjunto DEL Capota Y DEL Enrejado Vea Fig REMOCIÓN/REEMPLAZO DE LA TransmisiónOtros AlmacenamientoSistema DE Combustible Aceite DEL MotorProblema Causa Corrección Identificación DE ProblemasFuncionando cuando Pendiente Productos de consumo equipados con ruedas Garantía limitada Cómo Obtener Servicio Transmisión** Giro cero EZ y MZ Moldeada, no reforzada Service NOTES/ Aviso Service NOTES/ Aviso 11/15/13 AP