Husqvarna GT48XLSi warranty Check Tire Pressure, Check Deck Levelness, Check Brake System

Page 6

ASSEMBLY

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

All assembly instructions have been completed.

No remaining loose parts in carton.

Battery is properly prepared and charged.

Seat is adjusted comfortably and tightened securely.

All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

Ensure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

Check mower and drive belts. Ensure they are routed properly around pulleys and inside all belt keepers.

Check wiring. See that all connections are still secure and wires are properly clamped.

Before driving tractor, ensure freewheel control is in “transmission engaged” position (see “TO TRANS- PORT” in the Operation section of this manual).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

Engine oil is at proper level.

Fuel tank is filled with fresh, clean, regular unleaded gasoline.

Become familiar with all controls, their location and function. Operate them before you start the engine.

Ensure brake system is in safe operating condition.

Ensure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

It is important to purge the transmission before operat- ing your tractor for the first time. Follow proper start- ing and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

6

Image 6
Contents Operator’s Manual Manual de Operario English/SpanishGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo USE Throttle Control D See To USE Cruise Control J See FigTo Stop Mower Blades To Adjust Gauge Wheels See FigTo Operate Mower Reverse Operation System ROS See FigBattery INDICATOR/CHARGING Plug See Fig Battery Indicator Button See FigTo Transport See Fig Check Engine OIL Level Resetting Ignition System Passcode See FigBefore Starting the Engine ADD GasolinePRE-START Smartswitch Warning Lights See FigTo Start Engine StartingMowing Tips Purge TransmissionHour Meter General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Cleaning Deck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See O PSecure with small washer and small retainer spring as shown To Level Mower Mower, or, counterclockwise Loosen to lower Front mowerFront Wheel TOE-IN/CAMBER To Replace Mower Blade Drive BeltTo Check Brake PulleysTo Remove Wheel See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTo Replace LED Headlight To Start Engine with a Weak Battery See FigReplacing Battery See Fig Interlocks and RelaysREMOVAL/REPLACEMENT Smartswitch Ignition System Lights See FigTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control CableFuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXFuncionamiento General Reglas DE SeguridadAdvertencia II. Funcionamiento EN PendientesServicio III. NiñosIV. Remolque Manipulación Segura DE LA GasolinaTabla DE Materias Especificaciones DEL ProductoResponsabilidades DEL Cliente Herramientas Necesarias Para EL Montaje Piezas SIN MontarMontaje Para Remover EL Tractor DE LA Caja DE CartónRevisión DE LA Posición Adecuada DE Todas LAS Correas Revisión DE LA Presión DE LAS LlantasRevisión DE LA Nivelación DEL Conjunto Revisión DEL Sistema DE FrenosOperación Familiaricese CON SU Tractor Amperímetro Indica la carga + o la descarga de la bateríaComo Usar SU Tractor Para Ajustar EL Freno DE Estacionamiento Vea FigParada Vea Fig Cómo Usar EL Control DEL Cierre Diferencial Para Parar LAS Cuchillas DE LA Segadora Para Ajustar LAS Ruedas Calibradoras Vea FigPara Operar LA Segadora Sistema DE Operación EN Reversa ROS Vea FigFaros Delanteros Para Transportar Vea FigRemolquedecarretillasootrosaccesorios Testigo DE BATERÍA/CONECTOR DE Carga Vea FigAgregue Gasolina Antesde Hacerarrancar EL MotorRevise EL Nivel DE Aceite DEL Motor Para Operar DE LA Valvula DE Gasolina DE Reserva Vea FigArranque DEL Motor Consejos Para Segar Purgar LA TransmisiónContador Horario Tabla DE Lubricación MantenimientoRecomendaciones Generales Antes DE Cada USOCuidado DE LA Cuchilla TractorOperación DEL Freno LlantasMotor Limpieza Puerto DE Lavado DE LA Cubierta Vea Fig Servicio Y Ajustes Instale LA Segadora VeaBarra Antibalanceo S Instale la correa pasándola por encima de la polea del motor Para Nivelar LA Segadora Controlar Y Ajustar EL Freno Impresión / Inclinación DE LAS Ruedas DEL- AnterasMontaje DE LA Correa Para Cambiar LA Correa DE Impulsión DE Movimiento Vea FigDesmontaje DE LA Correa Para Remover LAS Ruedas Vea FigSustitución DEL Faro LED Para Hacer Arrancar EL Motor CON UNA BAT- Ería Baja Vea FigReemplazar LA Bateria Vea Fig Entrecierre Y ReléPara Remover EL Conjunto DEL Capota Y DEL Enrejado Vea Fig Luces DEL Sistema DE Arranque Smartswitch Vea FigTransmisión REMOCIÓN/REEMPLAZO DE LA TransmisiónSistema DE Combustible AlmacenamientoOtros Aceite DEL MotorIdentificación DE Problemas Problema Causa CorrecciónFuncionando cuando Pendiente Productos de consumo equipados con ruedas Garantía limitada Cómo Obtener Servicio Transmisión** Giro cero EZ y MZ Moldeada, no reforzada Service NOTES/ Aviso Service NOTES/ Aviso 11/15/13 AP