DnDial | Actiontec electronic IS560LH instruction

DnDial

This command instructs the modem to begin the dialing sequence. The dial string (n, including modifiers and the telephone number) is entered after the ATD com- mand.

A dial string can be up to 40 characters long. Any digit or symbol (0-9, *, #, A, B, C,

D)may be dialed as touch-tone digits. Characters such as spaces, hyphens, and pa- rentheses do not count, they are ignored by the modem and may be included in the dial string to enhance readability.

The following characters may be used as dial string modifiers:

		Redials last number. Should be the first character following
	L	ATD, ignored otherwise. The modem displays the dialing string
	L	in the following format: “Dialing…xxxxxxx” where “xxxxxxx” is the

		last number dialed.

	P	Pulse dialing. (e.g. ATDPxxx. Dialing set to pulse as default.)

	T	Touch-tone dialing (default). (e.g. ATDTxxx. Dialing set to tone
	T	as default.)
		as default.)

	,	Pause during dialing. Pause for time specified in Register S8
	,	before processing the next character in the dial string.
		before processing the next character in the dial string.

	W	Wait for dial tone. Modem waits for a second dial tone before
	W	processing the dial string.
		processing the dial string.

		Wait for quiet answer. Wait for five seconds of silence after
	@	dialing the number. If silence is not detected, the modem sends
		a NO ANSWER result code back to the user.

	!	Hook flash. Causes the modem to go on-hook for 0.5 seconds
	!	and then return to off-hook.
		and then return to off-hook.

		Return to command mode. Causes the modem to return to
	;	command mode after dialing the number, without disconnecting
		the call.

	^	Disable data calling tone transmission.

		Dial a telephone number previously stored using the &Zn=x
	S=n	command (see the &Zn=x command for further information).
		The range of n is 0-3.

	$	Bong tone detection.

41

Image 41

Actiontec electronic IS560LH user manual DnDial

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 Installations Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the Modem Devices Window Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices To The Modem Configuring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page AT&F&C1&D2W2 Modem’s Voice FeaturesInit String Page Windows 95 and Windows Troubleshooting More Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage Repeat Last Command AT CommandsAnswer Command +++ Escape sequence This command determines Ccitt vs. Bell standard Communication Standard SettingResult Codes Carrier Control DnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or off Select Pulse Dialing Return On-line to Data ModeResult Code Control Select Tone Dialing Result Code Option VnDCE Response Format Dial Tone Detect Extended Result Codes Long Space Disconnect Busy Tone DetectRecall Stored Profile Auto Retrain DTR Control Data Carrier Detect DCD Control Auxiliary Relay option 22bis Guard Tone Control This Command is effective only for use in Japan Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \Bn Zn=x\An \Kn Adjust Bits/s Rate ControlModem Port Flow Control Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity Timer Data Calling Tone \Xn XON/XOFF Pass Through V90=x V.90 Downstream Rate and Control AT Commands for Testing and Debugging Enable/Disable Data CompressionWrite to/Read from DSP Register Line-to-Line Loopback After initial negotiation Tion failedInitial Transmit Carrier Rate 33600 Rate Final Transmit Carrier Rate 33600Final Receive Carrier Rate 33600 Tion rate Registers Reference Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Comma Dial Modifier Time Range Default UnitssecondsConnection Completion Time-Out S11 Dtmf Dialing Speed S10 Automatic Disconnect DelayS12 Escape Guard Time S14 General Bit Mapped Options Status S22 S24 Timer to Control Sleep ModeS21 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40 S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier Result Code Summary DescriptionPage Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc