S28 Modulation Enable/Disable, S32 | Actiontec electronic IS560LH

S28	V.34 Modulation Enable/Disable

0= disabled, 1-255 = enabled, Range: 0-255

Default: 1

This register enables/disables V.34 modulation.

S30	Inactivity Timer

Range: 0-255

Default: 0

Units: minutes

S30 specifies the length of time (in minutes) that the modem will wait before discon- necting when no data is sent or received. This function is only applicable to buffer mode.

S32	Synthetic Ring Volume

Range: 0-255

Default: 10

This register specifies a synthetic ring volume in dB with an implied minus sign.

S33	Synthetic Ring Frequency

Range: 0-5

Default: 0

This register specifies a synthetic ring frequency. Valid ranges are 0-5, with 0= dis- abled and 1-5 corresponding to 5 ring frequencies.

S35	Data Calling Tone

0 = disabled, 1 = enableD Range: 0-1

Default: 0

Data Calling Tone is a tone of certain frequency and cadence as specified in V.25 which allows remote Data/FAX/Voice discrimination. The frequency is 1300 Hz with a cadence of .5 s on and 2 s off.

Page 70

Image 70

Actiontec electronic IS560LH S28 Modulation Enable/Disable, S30 Inactivity Timer, S32, S33, S35 Data Calling Tone

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This First Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 Installation Devices Window Installing The Modem Hardware Installation Installing The Modem Connecting Devices To The Modem Connecting Devices Configuring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Troubleshooting Windows 95 and Windows More Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage Answer Command AT CommandsRepeat Last Command +++ Escape sequence Result Codes Communication Standard SettingThis command determines Ccitt vs. Bell standard Carrier Control DnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation Handshake Result Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone Dialing VnDCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Recall Stored Profile Busy Tone DetectLong Space Disconnect Auto Retrain Data Carrier Detect DCD Control DTR Control 22bis Guard Tone Control Auxiliary Relay option Local Flow Control Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Pulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code \Xn XON/XOFF Pass Through Data Calling Tone V90=x V.90 Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line Loopback Initial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Final Receive Carrier Rate 33600 Final Transmit Carrier Rate 33600Rate Tion rate Registers Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −32 Default Backspace Units Connection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S12 Escape Guard Time S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S14 General Bit Mapped Options Status S21 S24 Timer to Control Sleep ModeS22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33 S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default Connection S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S40 S91 S89 Timer to Control Sleep ModeS90 S92 Result Code Summary Description No CarrierPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc

S28

V.34 Modulation Enable/Disable

S30

Inactivity Timer

S32

S33

S35

Data Calling Tone