Extended Result Codes | Actiontec electronic IS560LH specification

Xn	Result Code Selection and Call Progress Monitoring

This command enables tone detection options used in the dialing process. As these functions are chosen, the result codes are also affected. Therefore, this command is frequently used to control the modem chipset’s responses. The primary function of this control is to control the modem chip set’s call response capabilities.

Command	Result Code	Dial Tone Detect	Busy Tone Detect

X0	Disable	Disable	Disable

X1	Enable	Disable	Disable

X2	Enable	Enable	Disable

X3	Enable	Disable	Enable

X4	Enable	Enable	Enable (default)

X5	Enable	Enable	Enable

X6	Enable	Enable	Enable

X7	Disable	Enable	Enable

Extended Result Codes

	Extended	Effect
	Result Codes	Effect
	Result Codes

	Disabled	Displays only the basic result codes OK, CONNECT,
	Disabled	RING, NO CARRIER, and ERROR.
		RING, NO CARRIER, and ERROR.

		Displays basic result codes, along with the connect
	Enabled	message and the modem’s data rate, and an
	Enabled	indication of the modem’s error correction and data
		indication of the modem’s error correction and data
		compression operation.

	Dial Tone Detect

	Dial Tone	Effect
	Detect	Effect
	Detect

		The modem dials a call regardless of whether it detects
	Disabled	a dial tone. The period of time the modem waits before
		dialing is specified in register S6.

		The modem dials only upon detection of a dial tone,
	Enabled	and disconnects the call if the dial tone is not detected
		within 10 seconds.

47

Image 47

Actiontec electronic IS560LH user manual Extended Result Codes, Dial Tone Detect

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 Installations Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the Modem Devices Window Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices To The Modem Configuring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page AT&F&C1&D2W2 Modem’s Voice FeaturesInit String Page Windows 95 and Windows Troubleshooting More Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage +++ Escape sequence AT CommandsRepeat Last Command Answer Command Carrier Control Communication Standard SettingThis command determines Ccitt vs. Bell standard Result Codes DnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or off Select Tone Dialing Return On-line to Data ModeSelect Pulse Dialing Result Code Control Result Code Option VnDCE Response Format Dial Tone Detect Extended Result Codes Auto Retrain Busy Tone DetectLong Space Disconnect Recall Stored Profile DTR Control Data Carrier Detect DCD Control Auxiliary Relay option 22bis Guard Tone Control Pulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Local Flow Control Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \Bn Zn=x\An \Kn Adjust Bits/s Rate ControlModem Port Flow Control Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity Timer Data Calling Tone \Xn XON/XOFF Pass Through V90=x V.90 Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP Register After initial negotiation Tion failedInitial Transmit Carrier Rate 33600 Tion rate Final Transmit Carrier Rate 33600Rate Final Receive Carrier Rate 33600 Registers Reference Range −32 Default Backspace Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Comma Dial Modifier Time Range Default UnitssecondsConnection Completion Time-Out S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard Time S22 S24 Timer to Control Sleep ModeS21 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32 Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36 S40 S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S48 Lapm Error Control and Feature Negotiation default S92 S89 Timer to Control Sleep ModeS90 S91 No Carrier Result Code Summary DescriptionPage Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc