S40, S42 Auto Rate default 1, range | Actiontec electronic IS560LH

S38 = 5	38000 bits / s
S38 = 6	40000 bits / s
S38 = 7	42000 bits / s
S38 = 8	44000 bits / s
S38 = 9	46000 bits / s
S38 = 10	48000 bits / s
S38 = 11	50000 bits / s
S38 = 12	52000 bits / s
S38 = 13	54000 bits / s
S38 = 14	56000 bits / s
S40	ETC Startup Autorating (default 0, range 0-2)
Range:	0-2
Default:	0
S20=0	Startup with normal autorating.
S20=1	Startup at initial rate of 4800 or below.
S20=2	Startup at initial rate of 9600 or below.
S42	Auto Rate (default 1, range 0-1)
0 = auto rate disabled, 1 = enabled.
Range:	0-1
Default:	1

This command is used for testing and debugging only. V.32bis and V.22bis auto rate is disabled. Retrain operation is disabled or enabled in data mode, and fallback is disabled in data mode.

S43	Auto Mode (default 1, range 0-1)

0 = auto mode disabled, 1 = enabled

Range: 0-1

Default: 1

This command is used for testing and debugging only. V.32bis startup auto mode operation is disabled.

S48	LAPM Error Control and Feature Negotiation (default 7)
S48 =	7	Negotiation enabled.
S 48 = 128		Negotiation disabled; forces immediate fallback options
		specified in S36.

72

Image 72

Actiontec electronic IS560LH user manual S40, S42 Auto Rate default 1, range, S43 Auto Mode default 1, range

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This First Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 Installation Devices Window Installing The Modem Hardware Installation Installing The Modem Connecting Devices To The Modem Connecting Devices Configuring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Troubleshooting Windows 95 and Windows More Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage AT Commands Repeat Last CommandAnswer Command +++ Escape sequence Communication Standard Setting This command determines Ccitt vs. Bell standardResult Codes Carrier Control DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information This command turns the speaker on or off Modulation Handshake Return On-line to Data Mode Select Pulse DialingResult Code Control Select Tone Dialing VnDCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Busy Tone Detect Long Space DisconnectRecall Stored Profile Auto Retrain Data Carrier Detect DCD Control DTR Control 22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications Mode This Command is effective only for use in JapanLocal Flow Control Selection Pulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code \Xn XON/XOFF Pass Through Data Calling Tone V90=x V.90 Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line Loopback Tion failed Initial Transmit Carrier Rate 33600After initial negotiation Final Transmit Carrier Rate 33600 RateFinal Receive Carrier Rate 33600 Tion rate Registers Reference Range 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Range Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S10 Automatic Disconnect Delay S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options Status S24 Timer to Control Sleep Mode S21S22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33 S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 Connection S42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40 S89 Timer to Control Sleep Mode S90S91 S92 Result Code Summary Description No CarrierPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc