Manuals / Actiontec electronic / Computer Equipment / Network Router

Actiontec electronic IS560LH user manual VnDCE Response Format, Result Code Option

Models: IS560LH

1 77

Download 77 pages 15.67 Kb

Page 46

VnDCE Response Format

This command controls whether result codes (including call progress and negotia- tion progress messages) are displayed as words or their numeric equivalents.

	Command		Effect

	V0		Not supported. Results are always text.

	V1		Displays result codes as text (default).

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

Wn			Result Code Option

	Command			Effect

	W0			CONNECT result code reports DTE speed. Disable
	W0			protocol result codes.
				protocol result codes.

	W1			CONNECT result code reports DTE speed. Enable
	W1			protocol result codes.
				protocol result codes.

	W2			CONNECT result code reports DCE speed. Enable
	W2			protocol result codes (default).
				protocol result codes (default).

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

46

Image 46

Actiontec electronic IS560LH user manual VnDCE Response Format, Result Code Option

Contents

V.90 Internal Voice/Fax Windows Modem Users ManualInstalling The Modem Proprietary Notice and DisclaimerTable of Contents Installing and Configuring Communications SoftwareActiontec Electronics, Inc IntroductionContacting Actiontec Customer Support PhoneDo This First For Windows 95 and Windows 98 InstallationsFigure 1 The Modems Properties Panel Figure 2 Windows 95 IRQ Resources Dialog Box Figure 3a COM2 Properties Dialog Box Figure 3b Windows 95 or 95A COM2 Disable Panel For Windows NT 4.0 InstallationFig. 4 Devices Window Hardware Installation Installing The ModemFigure 5 Removing the Backplate Figure 6 Installing The Modem Connecting Devices To The Modem Fig.7 Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Configuring WindowsPage Page Page Page Page Your modem is now installed and configured for use with Windows Configuring Windows NT Page Step 7 Restart your computer Step 11 Click Continue to finish the installation The Modem’s Voice Features Installing and Configuring Communications SoftwareAT&F&C1&D2W2 Page Step 1 Check System Resources TroubleshootingWindows 95 and Windows Step 2 Check Modem PropertiesStep 3 Modem Diagnostics Figure 8 More Info PanelStep 4 Does Not Install Uninstalling the ModemNote to users of Windows 95 and Note to users of Windows NT Nothing Appears On The Screen When I Type Common ProblemsNo Dialtone Error Communications Software Does Not Workwhen the modem is in use. This includes extension phones, answering machines, cordless phone bases, caller ID boxes and their cables. This reduces the load on your phone line and keeps signal attenuation to a minimum Repeat Last Command Appendix A AT Command SetAT Commands Answer CommandCommunication Standard Setting Carrier ControlDnDial Online Data Character Echo Command Echo CommandHook Control Returns default speed and controller firmware version Monitor Speaker VolumeRequest ID Information Calculates ROM checksum and displays it on the DTEModulation Handshake Monitor Speaker ModeResult Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone DialingVnDCE Response Format Result Code OptionDial Tone Detect Extended Result CodesResult Code Selection and Call Progress Monitoring Recall Stored Profile Busy Tone DetectLong Space Disconnect V.32 Auto RetrainDCD turns on when the remote modem’s carrier signal Data Carrier Detect DCD ControlDTR Control mode, the modem disconnects default. If this signal isAuxiliary Relay option V.22bis Guard Tone ControlLoad Factory Settings Pulse Dial Make-to-Break Ratio Selection Local Flow Control SelectionAsynchronous Communications Mode n = 0, 1V.42 or MNP error control mode. If neither error control Data Set Ready DSR OptionAsynchronous Communications Mode View Active Configuration and Stored Profile This command is used to display the active profilesBelow is an example of a possible output Store Current Configuration Select Stored Profile for Hard ResetSelect Maximum MNP Block Size Zn=xStore Telephone Number Transmit Break to RemoteModem Port Flow Control Adjust Bits/s Rate ControlBreak Control Result Codes V.42, MNP, or buffer default. The modem attempts to Error Control Mode Selectionconnect in MNP 2-4 error control procedure. If this fails Local Flow Control SelectionInactivity Timer Ring indicator signal off after the telephone call is answeredCompatibility command Protocol Result CodeXON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control View Numbers in BlacklistWrite to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackATI11 Self-Test CommandsDescription S-Registers Reference Ring Counter Command Line Termination Character user definedCommand Line Editing Character user defined AT Escape Character user definedComma Dial Modifier Time Connection Completion Time-OutWait Before Dialing Escape Guard Time Automatic Disconnect DelayDTMF Dialing Speed General Bit Mapped Options StatusTimer to Control Sleep Mode Synthetic Ring Volume V.34 Modulation Enable/DisableInactivity Timer Data Calling Tone56K Dial Line Rate default Dial Line Rate defaultNegotiation Fallback default LAPM Error Control and Feature Negotiation default Auto Rate default 1, rangeAuto Mode default 1, range ETC Startup Autorating default 0, rangeLocal Phone Status Timer to Control Sleep ModeDirect Connect Transmit Level default Line Transmit LevelResult Code Modem lost carrier signal, or does not detect carrierThe Result Code Summary DescriptionV42bis-V.42 error control and V.42bis data compression FCC Part 68 Requirements Appendix B Communications RegulationsFCC Regulations Declaration of ConformityCanadian Department Of Communications CDOC