Actiontec electronic IS560LH manual

CONNECT 34666 EC* CONNECT 36000 EC* CONNECT 37333 EC* CONNECT 38666 EC* CONNECT 40000 EC* CONNECT 41333 EC* CONNECT 42666 EC* CONNECT 44000 EC* CONNECT 45333 EC* CONNECT 46666 EC* CONNECT 48000 EC* CONNECT 49333 EC* CONNECT 50666 EC* CONNECT 52000 EC* CONNECT 53333 EC*

Connection at 34666 bits/s, V.90 rate Connection at 36000 bits/s, V.90 rate Connection at 37333 bits/s, V.90 rate Connection at 38666 bits/s, V.90 rate Connection at 40000 bits/s, V.90 rate Connection at 41333 bits/s, V.90 rate Connection at 42666 bits/s, V.90 rate Connection at 44000 bits/s, V.90 rate Connection at 45333 bits/s, V.90 rate Connection at 46666 bits/s, V.90 rate Connection at 48000 bits/s, V.90 rate Connection at 49333 bits/s, V.90 rate Connection at 50666 bits/s, V.90 rate Connection at 52000 bits/s, V.90 rate Connection at 53333 bits/s, V.90 rate

*EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used:

V42bis—V.42 error control and V.42bis data compression.

V42—V.42 error control only.

MNP 5— MNP class 4 error control and MNP class 5 data compression.

MNP 4— MNP class 4 error control only.

NoEC—No error control protocol.

75

Image 75

Actiontec electronic IS560LH user manual

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 Installations Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the Modem Devices Window Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices To The Modem Configuring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Windows 95 and Windows Troubleshooting More Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage +++ Escape sequence AT CommandsRepeat Last Command Answer Command Carrier Control Communication Standard SettingThis command determines Ccitt vs. Bell standard Result Codes DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or off Select Tone Dialing Return On-line to Data ModeSelect Pulse Dialing Result Code Control Result Code Option VnDCE Response Format Dial Tone Detect Extended Result Codes Auto Retrain Busy Tone DetectLong Space Disconnect Recall Stored Profile DTR Control Data Carrier Detect DCD Control Auxiliary Relay option 22bis Guard Tone Control Pulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Local Flow Control Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity Timer Data Calling Tone \Xn XON/XOFF Pass Through V90=x V.90 Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP Register Tion failed Initial Transmit Carrier Rate 33600After initial negotiation Tion rate Final Transmit Carrier Rate 33600Rate Final Receive Carrier Rate 33600 Registers Reference Range −32 Default Backspace Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Range Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard Time S24 Timer to Control Sleep Mode S21S22 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32 Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36 S40 S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S48 Lapm Error Control and Feature Negotiation default S92 S89 Timer to Control Sleep ModeS90 S91 No Carrier Result Code Summary DescriptionPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc