Installing The Modem | Actiontec electronic IS560LH guide

Installing The Modem

Always discharge static electricity before handling your modem. You may discharge static electricity by touching a grounded metal structure or by using any commercially available grounding strap.

Make sure the expansion slot type is 16-bit, which has two slots to fit the ISA card. 8-bit slots have only one connector. If you use an 8-bit slot, the modem will not have access to the higher interrupts (IRQ 9-12).

The position of the expansion slots in your computer may differ from the illustration shown but the installation procedure should be the same.

Hardware Installation

1.Turn off the computer and all peripheral devices connected to it.

2.Unplug the computer power cord from the wall receptacle.

3.Remove the computer’s cover. Refer to your computer owner’s manual for instructions.

4.Remove the screw securing the expansion slot cover behind one of the computer’s available 16-bit ISA expansion slots. Lift the expansion slot cover out as shown below.

Figure 5: Removing the Backplate

9

Image 9

Actiontec electronic IS560LH user manual Installing The Modem, Hardware Installation

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 Installations Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the Modem Devices Window Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices To The Modem Configuring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Windows 95 and Windows Troubleshooting More Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage Repeat Last Command AT CommandsAnswer Command +++ Escape sequence This command determines Ccitt vs. Bell standard Communication Standard SettingResult Codes Carrier Control DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or off Select Pulse Dialing Return On-line to Data ModeResult Code Control Select Tone Dialing Result Code Option VnDCE Response Format Dial Tone Detect Extended Result Codes Long Space Disconnect Busy Tone DetectRecall Stored Profile Auto Retrain DTR Control Data Carrier Detect DCD Control Auxiliary Relay option 22bis Guard Tone Control This Command is effective only for use in Japan Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity Timer Data Calling Tone \Xn XON/XOFF Pass Through V90=x V.90 Downstream Rate and Control AT Commands for Testing and Debugging Enable/Disable Data CompressionWrite to/Read from DSP Register Line-to-Line Loopback Tion failed Initial Transmit Carrier Rate 33600After initial negotiation Rate Final Transmit Carrier Rate 33600Final Receive Carrier Rate 33600 Tion rate Registers Reference Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Range Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S11 Dtmf Dialing Speed S10 Automatic Disconnect DelayS12 Escape Guard Time S14 General Bit Mapped Options Status S24 Timer to Control Sleep Mode S21S22 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40 S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier Result Code Summary DescriptionPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc