Sse | Actiontec electronic IS560LH guide

Option	Selection	AT Cmd
No Carrier Disc	2000 msec	S10
DTMF Dial Speed	95 msec	S11
Escape GuardTime	1000 msec	S12
Data Calling Tone	Disabled	S35
Line Rate	33600	S37
DSVD mode	Disabled	-SSE

Stored Phone Numbers

&Z0=

&Z1=

&Z2=

&Z3=

OK

&Wn	Store Current Configuration

This command stores certain command options and S-register values into the modem’s nonvolatile memory. The ATZ command or a powerup reset of the modem restores this profile.

Result Codes:

OK	n = 0

ERROR	Otherwise

&Yn	Select Stored Profile for Hard Reset

This command does not change the behavior of the modem but is included for com- patibility with applications that issue the &Y0 command:

Command	Effect

&Y0	Select stored profile 0 on powerup

&Y1	ERROR

Result Codes:

OK

n = 0

ERROR Otherwise

54

Image 54

Actiontec electronic IS560LH user manual Sse

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This First Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 Installation Devices Window Installing The Modem Hardware Installation Installing The Modem Connecting Devices To The Modem Connecting Devices Configuring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Modem’s Voice Features Init StringAT&F&C1&D2W2 Page Troubleshooting Windows 95 and Windows More Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage Answer Command AT CommandsRepeat Last Command +++ Escape sequence Result Codes Communication Standard SettingThis command determines Ccitt vs. Bell standard Carrier Control DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information This command turns the speaker on or off Modulation Handshake Result Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone Dialing VnDCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Recall Stored Profile Busy Tone DetectLong Space Disconnect Auto Retrain Data Carrier Detect DCD Control DTR Control 22bis Guard Tone Control Auxiliary Relay option Local Flow Control Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Pulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code \Xn XON/XOFF Pass Through Data Calling Tone V90=x V.90 Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line Loopback Tion failed Initial Transmit Carrier Rate 33600After initial negotiation Final Receive Carrier Rate 33600 Final Transmit Carrier Rate 33600Rate Tion rate Registers Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −32 Default Backspace Units Range Default Unitsseconds Connection Completion Time-OutComma Dial Modifier Time S12 Escape Guard Time S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S14 General Bit Mapped Options Status S24 Timer to Control Sleep Mode S21S22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33 S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default Connection S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S40 S91 S89 Timer to Control Sleep ModeS90 S92 Result Code Summary Description No CarrierPage FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc