Windows 95 IRQ Resources Dialog Box | Actiontec electronic IS560LH

If you are going to use the Telephone Answering Machine (TAM) functions of the modem and you are running Windows 95, you need to install a software component called Unimodem V. If you have Windows 95 OEM Service Release 2 (Version 4.00.950 B) or a later version of Windows, this component comes standard as part of the operating system.

To find out which version of Windows 95 you are using, right click the My Com- puter icon on the desktop, and choose Properties from the menu that appears. If the version of Windows 95 is 4.00.950 or 4.00.950A, go to the UNIMODEM directory of the CD-ROM that came with your modem and right-click on the UNIMODV.INF icon, (this may be named UNIMODV) then click on Install.. Restart your computer to enable the drivers.

Make sure you have an available COM port and IRQ on your computer. The mo- dem needs one IRQ and one COM Port in order to function. To check which inter- rupts are available on your system, double-click on the System icon in Control Panel and click the Device Manager tab. Highlight Computer in the dialog box and click Properties. There are only 16 (0 to 15) interrupts in a PC system. Make a note of any interrupt not listed.

Figure 2: Windows 95 IRQ Resources Dialog Box

If you do not have any free interrupts you may need to disable a COM port for an installed device that you are not currently using, such as COM2.

5

Image 5

Actiontec electronic IS560LH user manual Windows 95 IRQ Resources Dialog Box

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 Installations Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box For Windows NT 4.0 Installation Proceed to the section titled Installing the Modem Devices Window Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices To The Modem Configuring Windows Page Page Finish Configuring Windows 95 OEM SR2Page Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page AT&F&C1&D2W2 Modem’s Voice FeaturesInit String Page Windows 95 and Windows Troubleshooting More Info Panel Uninstalling the Modem Does Not InstallPage Page No Dialtone Error Common ProblemsPage Repeat Last Command AT CommandsAnswer Command +++ Escape sequence This command determines Ccitt vs. Bell standard Communication Standard SettingResult Codes Carrier Control DnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or off Select Pulse Dialing Return On-line to Data ModeResult Code Control Select Tone Dialing Result Code Option VnDCE Response Format Dial Tone Detect Extended Result Codes Long Space Disconnect Busy Tone DetectRecall Stored Profile Auto Retrain DTR Control Data Carrier Detect DCD Control Auxiliary Relay option 22bis Guard Tone Control This Command is effective only for use in Japan Asynchronous Communications ModeLocal Flow Control Selection Pulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \Bn Zn=x\An \Kn Adjust Bits/s Rate ControlModem Port Flow Control Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity Timer Data Calling Tone \Xn XON/XOFF Pass Through V90=x V.90 Downstream Rate and Control AT Commands for Testing and Debugging Enable/Disable Data CompressionWrite to/Read from DSP Register Line-to-Line Loopback After initial negotiation Tion failedInitial Transmit Carrier Rate 33600 Rate Final Transmit Carrier Rate 33600Final Receive Carrier Rate 33600 Tion rate Registers Reference Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Comma Dial Modifier Time Range Default UnitssecondsConnection Completion Time-Out S11 Dtmf Dialing Speed S10 Automatic Disconnect DelayS12 Escape Guard Time S14 General Bit Mapped Options Status S22 S24 Timer to Control Sleep ModeS21 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40 S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier Result Code Summary DescriptionPage Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc