Actiontec electronic IS560LH specs

Step 6 Select the Resource Settings which do not cause any conflicts with other devices.

Step 7 Restart your computer.

Step 8 Click on the Modems icon in the Control Panel. Verify that Windows NT has correctly found the modem.

Step 9 If you wish to use your modem to dial into a Windows NT Remote Access Server or wish to connect to the Internet, you will need to configure Dial- up Networking. If you do not see the Remote Access Setup Panel installation, In Control Panel double-click the Network icon. Click on the Services folder and select Remote Access Service. If no Remote Access Service option is listed click Add. Select Remote Access Service. and click OK. Windows NT may ask for its own CD-ROM for some files. Insert as required. After you have installed Remote Access Service add the appropriate protocols as directed.

28

Image 28

Actiontec electronic IS560LH user manual

Contents

Internal Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This First Windows 95 IRQ Resources Dialog Box COM2 Properties Dialog Box Proceed to the section titled Installing the Modem For Windows NT 4.0 Installation Devices Window Installing The Modem Hardware Installation Installing The Modem Connecting Devices To The Modem Connecting Devices Configuring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Page Page Page Page Page Page Configuring Windows NT Page Page Page Init String Modem’s Voice FeaturesAT&F&C1&D2W2 Page Troubleshooting Windows 95 and Windows More Info Panel Does Not Install Uninstalling the ModemPage Page Common Problems No Dialtone ErrorPage AT Commands Repeat Last CommandAnswer Command +++ Escape sequence Communication Standard Setting This command determines Ccitt vs. Bell standardResult Codes Carrier Control DnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation Handshake Return On-line to Data Mode Select Pulse DialingResult Code Control Select Tone Dialing VnDCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Busy Tone Detect Long Space DisconnectRecall Stored Profile Auto Retrain Data Carrier Detect DCD Control DTR Control 22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications Mode This Command is effective only for use in JapanLocal Flow Control Selection Pulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code \Xn XON/XOFF Pass Through Data Calling Tone V90=x V.90 Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line Loopback Initial Transmit Carrier Rate 33600 Tion failedAfter initial negotiation Final Transmit Carrier Rate 33600 RateFinal Receive Carrier Rate 33600 Tion rate Registers Reference Range 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsRange −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Connection Completion Time-Out Range Default UnitssecondsComma Dial Modifier Time S10 Automatic Disconnect Delay S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options Status S21 S24 Timer to Control Sleep ModeS22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33 S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 Connection S42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S40 S89 Timer to Control Sleep Mode S90S91 S92 Result Code Summary Description No CarrierPage FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc