Manuals / Actiontec electronic / Computer Equipment / Network Router

Actiontec electronic IS560LH user manual V.22bis Guard Tone Control, Auxiliary Relay option

Models: IS560LH

1 77

Download 77 pages 15.67 Kb

Page 50

&Fn	Load Factory Settings

This command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the S-register settings in the ac- tive configuration with factory values.

	Command		Effect

	&F0		Recall factory setting as active configuration. (default)

&Gn		V.22bis Guard Tone Control

This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.

	Command		Effect

	&G0		Guard tone disabled (default).

	&G1		Sets guard tone to 550 Hz.

	&G2		Sets guard tone to 1800 Hz.

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

&Jn		Auxiliary Relay option

	Command		Effect

	&J0		The auxiliary relay is never closed.

	&J1		NOT SUPPORTED, responds ERROR.

Result Codes:

	OK	n = 0

	ERROR	Otherwise

50

Image 50

Actiontec electronic IS560LH user manual V.22bis Guard Tone Control, Auxiliary Relay option, Load Factory Settings

Contents

V.90 Internal Voice/Fax Windows Modem Users ManualInstalling The Modem Proprietary Notice and DisclaimerTable of Contents Installing and Configuring Communications SoftwareActiontec Electronics, Inc IntroductionContacting Actiontec Customer Support PhoneFigure 1 The Modems Properties Panel For Windows 95 and Windows 98 InstallationsDo This First Figure 2 Windows 95 IRQ Resources Dialog Box Figure 3a COM2 Properties Dialog Box Figure 3b Windows 95 or 95A COM2 Disable Panel For Windows NT 4.0 InstallationFig. 4 Devices Window Figure 5 Removing the Backplate Installing The ModemHardware Installation Figure 6 Installing The Modem Connecting Devices To The Modem Fig.7 Connecting DevicesConfiguring Windows Page Page Configuring Windows 95 OEM SR2 FinishPage Page Page Next Configuring WindowsPage Page Page Page Page Your modem is now installed and configured for use with Windows Configuring Windows NT Page Step 7 Restart your computer Step 11 Click Continue to finish the installation AT&F&C1&D2W2 Installing and Configuring Communications SoftwareThe Modem’s Voice Features Page Step 1 Check System Resources TroubleshootingWindows 95 and Windows Step 2 Check Modem PropertiesStep 3 Modem Diagnostics Figure 8 More Info PanelStep 4 Does Not Install Uninstalling the ModemNote to users of Windows 95 and Note to users of Windows NT Nothing Appears On The Screen When I Type Common ProblemsNo Dialtone Error Communications Software Does Not Workwhen the modem is in use. This includes extension phones, answering machines, cordless phone bases, caller ID boxes and their cables. This reduces the load on your phone line and keeps signal attenuation to a minimum Repeat Last Command Appendix A AT Command SetAT Commands Answer CommandCommunication Standard Setting Carrier ControlDnDial Hook Control Echo CommandOnline Data Character Echo Command Returns default speed and controller firmware version Monitor Speaker VolumeRequest ID Information Calculates ROM checksum and displays it on the DTEModulation Handshake Monitor Speaker ModeResult Code Control Return On-line to Data ModeSelect Pulse Dialing Select Tone DialingVnDCE Response Format Result Code OptionResult Code Selection and Call Progress Monitoring Extended Result CodesDial Tone Detect Recall Stored Profile Busy Tone DetectLong Space Disconnect V.32 Auto RetrainDCD turns on when the remote modem’s carrier signal Data Carrier Detect DCD ControlDTR Control mode, the modem disconnects default. If this signal isLoad Factory Settings V.22bis Guard Tone ControlAuxiliary Relay option Pulse Dial Make-to-Break Ratio Selection Local Flow Control SelectionAsynchronous Communications Mode n = 0, 1Asynchronous Communications Mode Data Set Ready DSR OptionV.42 or MNP error control mode. If neither error control Below is an example of a possible output This command is used to display the active profilesView Active Configuration and Stored Profile Store Current Configuration Select Stored Profile for Hard ResetSelect Maximum MNP Block Size Zn=xStore Telephone Number Transmit Break to RemoteBreak Control Adjust Bits/s Rate ControlModem Port Flow Control Result Codes V.42, MNP, or buffer default. The modem attempts to Error Control Mode Selectionconnect in MNP 2-4 error control procedure. If this fails Local Flow Control SelectionInactivity Timer Ring indicator signal off after the telephone call is answeredCompatibility command Protocol Result CodeXON/XOFF Pass Through Data Calling ToneV90=x V.90 Downstream Rate and Control View Numbers in BlacklistWrite to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackATI11 Self-Test CommandsDescription S-Registers Reference Ring Counter Command Line Termination Character user definedCommand Line Editing Character user defined AT Escape Character user definedWait Before Dialing Connection Completion Time-OutComma Dial Modifier Time Escape Guard Time Automatic Disconnect DelayDTMF Dialing Speed General Bit Mapped Options StatusTimer to Control Sleep Mode Synthetic Ring Volume V.34 Modulation Enable/DisableInactivity Timer Data Calling ToneNegotiation Fallback default Dial Line Rate default56K Dial Line Rate default LAPM Error Control and Feature Negotiation default Auto Rate default 1, rangeAuto Mode default 1, range ETC Startup Autorating default 0, rangeLocal Phone Status Timer to Control Sleep ModeDirect Connect Transmit Level default Line Transmit LevelResult Code Modem lost carrier signal, or does not detect carrierThe Result Code Summary DescriptionV42bis-V.42 error control and V.42bis data compression FCC Part 68 Requirements Appendix B Communications RegulationsFCC Regulations Declaration of ConformityCanadian Department Of Communications CDOC