Fs/Lr Sol | Actron CP9190 specs

		PID Definitions
			PID		Extended Description
			FS/LR SOL		Fail Safe / Low / Reverse Solenoid
			FUEL/LEAN MON		Fuel / Lean Monitor
			FUEL/RICH MON		Fuel / Rich Monitor
			FUEL CELL ID		Fuel Cell ID
			FUEL CNTRLSTAT		Fuel Control Status
			FUEL CUTOFF		Fuel Cutoff
			FUEL FLO SIG		Fuel Flow Signal
			FUEL FLOW SIG		Fuel Flow Signal
			FUEL INJ 1		Fuel Injector #1
			FUEL INJ 2		Fuel Injector #2
			FUEL INJ 3		Fuel Injector #3
			FUEL INJ 4		Fuel Injector #4
			FUEL INJ 5		Fuel Injector #5
			FUEL INJ 6		Fuel Injector #6
			FUEL INJ 7		Fuel Injector #7
			FUEL INJ 8		Fuel Injector #8
			FUEL INJ 9		Fuel Injector #9
			FUEL INJ 10		Fuel Injector #10
			FUEL INJ (S) 1		Fuel Injector #1
			FUEL INJ (S) 2		Fuel Injector #2
			FUEL INJ (S) 3		Fuel Injector #3
			FUEL INJ (S) 4		Fuel Injector #4
			FUEL INJ (S) 5		Fuel Injector #5
			FUEL INJ (S) 6		Fuel Injector #6
			FUEL INJ (S) 7		Fuel Injector #7
			FUEL INJ (S) 8		Fuel Injector #8
			FUEL INJ (S) 9		Fuel Injector #9
			FUEL INJ (S) 10		Fuel Injector #10
			FUEL LEVEL		Fuel Level Sensor
			FUEL LVL		Fuel Level
			FUEL MON SIG		Fuel Monitor Signal
			FUEL MONITOR		Fuel Monitor Completed This Driving Cycle
			FUEL PMP SPD		Fuel Pump Speed
			FUEL PRES (PSIG)/(KPA)		Fuel System Pressure
			FUEL PUMP		Fuel Pump
			FUEL PUMP REL		Fuel Pump Relay
			FUEL PUMP RLY		Fuel Pump Relay Control
			FUEL PUMP(V)		Fuel Pump Supply Voltage
			FUEL PW1(MS)		Fuel Injector Pulse Width Control
			FUEL PW2(MS)		Fuel Injector Pulse Width Control
			FUEL PW B1		Fuel Injector Pulse Width (Left)
			FUEL PW B2		Fuel Injector Pulse Width (Right)
			FUEL RAIL PRS		Fuel Rail Pressure
			FUEL RATE		Fuel Rate
			FUEL SHUTSTAT		Fuel Shutoff Valve Status
A
			FUEL STATUS 1		Fuel System 1 Loop Status
			FUEL STATUS 2		Fuel System 2 Loop Status
			FUEL SYS		Rich/lean Fuel System States
			FUEL SYS 1		Fuel System 1 Loop Status
			FUEL SYS 2		Fuel System 2 Loop Status
			FUEL SYS BK1		Rich/lean Bank 1
			FUEL SYS BK2		Rich/lean Bank 2
			FUEL SYS TEST		Fuel System Test
			FUEL SYS TST		Fuel System Test

A – 18 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Image 198

Actron CP9190 manual Fs/Lr Sol

Contents

CP9190 Elite AutoScanner Pro HW Ver Boot Ver Prod ID Board ID Burn Date Burn Loc Serial NoTechnical Support Table of Contents Global OBD II Diagnostics Import Diagnostics Troubleshooting Safety Precautions Type Styles Used Icons used Important Safety Messages Avoid sparks when connecting or disconnecting Battery terminals. Do not place uninsulated metalTools on the battery Power leads to the battery Do not touch eyes while working near battery Have plenty of fresh water and soap nearby Risk of fire Short circuits can cause injury Engine compartment contains electrical connections N D L Do not leave a running engine unattended An air bag opening can cause injury Equipment Tips and Lists Safety MessagesCheck Note Equipment Damage Questions and Responses Functions and SelectionsMenus Manual References Getting Started Introduction Using the CD Installing Applications On Included CD Close all programs on the computer Place the CD in CD-Drive European Vehicles Vehicle Service InformationDomestic Vehicles Web Site Asian Vehicles Web Site Other Manuals Repair Information ProgramsSuitable Manual Titles Introduction to On-Board Diagnostics OBD GM On-Board Diagnostics SAE Publications Ford On-Board Diagnostics Data Link Connector DLC OBD II J1962 Data Link Connector DLC Pins Ford Historic Mecs Cable Adapter Vehicle DLC Vehicle DLC GM Historic Use the cigarette lighter cable to provide 12V to the tool Chrysler Historic OBD II Diagnostic Trouble Codes DTCs 1 0 Lower Upper Assigned DTC System Using The Scan Tool Scan Tool Internal Power 9V Battery External Power 7 to 16 Volts SpecificationsOperating Temperature 0 to 50C 32 to 122F Power Dissipation 5 Watts maximum Dimensions Height Included with Scan Tool Included with Scan Tool Display Keypad Power Internal Battery Vehicle Power Scan Tool Power UP System SetupSystem Setup allows From Main Menu 1.Select System Setup From System Setup screen Select English/MetricChanging Measurement Units Save Measurement Setting. Press Enter Changing Display ContrastSelect Desired Measurement Unit Setup menu From System Setup menuBeeper System Setup menu Changing Auto-Power OffSave Beeper sound setting Select desired Beeper sound choice Increase or Decrease Auto Power Off Time Save Auto Power Off Time. Press EnterView Tool Information Display Test Return to Setup Tool Menu. Use the Back keyFrom System Setup menu Select Display Test View Information When Done, Press Back Key Start Display TestLook for Missing Spots Memory Test From System Setup menu Select Keyboard TestKeyboard Test Press a KEY UP or Down arrow From System Setup menu Select Memory TestReturn to System Setup menu Memory Test may take 2-9 of Getting Started Connecting The Scan ToolProgram Mode Connect appropriate cable to Scan Tool Remove DLC cover if required Review DataFind DLC on vehicle Connect cable to vehicle Playback Follow prompts and instructions provided by Scan ToolSelect Playback Play Back Recording Down arrow Print Data Return to Review Data menu. Press Back From Special Tests menu Select Print Data Select Data To Be Printed. Use UP or Down arrow key Code Lookup Return to Select Print Data screenSelect Code Lookup P0001 Enter code P1575 Select Setup User Key Setup User KeyFrom Tool Setup Menu Key until Setup User Key is Select desired vehicle to diagnose Vehicle SelectionFrom Main Menu Confirm selection Confirm selection Follow Instructions on the display Using The Scan Tool Global OBD II Diagnostics Datastream Menu Global Function ListGlobal Function List is Special Tests Menu Code Lookup Tool Setup Menu Datastream Menu View Data From Datastream Menu Select View DataObserve while Scan Tool validates PID MAP View Entire List From Select Data to View menu Select Entire Data ListView PIDs on Scan Tool. Use UP or Down arrow key Return to Datastream Menu Press BackCustom List Select Select View Instructions or Not Select PIDs to View Customize Lines Record Data Select Display Lines Refer to View Data to setup Custom List or View Entire List From Datastream Menu Select Record Data From the Pick Trigger Method Screen Diagnostic Codes Menu Diagnostic Codes MenuRead Codes From Diagnostic Codes Menu Select Read Codes View and write down DTCs Return to Diagnostic Codes Menu Pending Codes From the Diagnostic Codes Menu Select Pending Codes If Pending Codes are Present From Diagnostic Codes Menu Select Erase Codes Erase Codes Select Yes to erase diagnostic results and codes Prepare Vehicle. Turn key on. Leave engine off. Press Enter Observe Command Sent message is displayed Return to Diagnostic Codes Menu. Press EnterView Freeze Data Select Frame if more than 1 frame is present Return to Diagnostic Codes Menu Press BackSpecial Tests Menu Select another frame to view if available Readiness I/M Readiness Menu From the Special Tests Menu Select I/M ReadinessThis Drive Cycle. If vehicle View Summary of Monitor Status Abbreviated Name Expanded Name Return to Special Tests Menu. Press Back Drive Cycle Monitor Clear Monitors by Press Enter Two types of Drive Cycle Monitors are Return to Special Tests Menu State OBD Check O2 Monitor Test Following O2 Sensor Tests are available Select O2 Sensor Diagnostic Monitor Tests From the Special Tests Menu Select Diag Mon Tests Non-CAN Vehicles Can Vehicles Return to Select Test Menu Back key Select On-Board Systems On-Board SystemsFrom the Special Tests Menu Key until On-Board Systems Vehicle Info Select Vehicle Info VIN Return to Special Tests Menu Press Back or key Modules Present SAE J1850 protocol is shown as Vpwm or PWM ISO 14230-4 protocol is shown as K2K Keyword Global OBD II Diagnostics GM Function List GM Function List is broken down into the following menus Review Data Print Data Read Codes Playback Use UP or Down arrow key until View Data is highlighted Never operate the Scan Tool while driving. HaveFrom the Datastream Menu 1.Select View Data Multiple Group Vehicles From the Datastream Menu 1.Select Record Data View PIDs on Scan ToolChange Custom Data List Parameters Use UP or Down arrow key until Record Data is highlight Select Trigger Method Recording. Trigger on Codes will Review Data Return to Datastream Menu. Press Back From the Diagnostic Codes Menu Select Read Codes 45ENG From the Diagnostic Codes Menu Select Erase Codes Use UP or Down arrow key until Erase Codes is highlighted Manual Erase Methods Use UP or Down arrow key until Field Service is highlighted Field ServiceFrom the Special Tests Menu Select Field Service Check vehicle malfunction indicator lamp MIL Koeo Procedure Code 12 will look likeCode 23 will look like Koer Procedure GM Enhanced OBD II Diagnostics Code Lookup Tool Setup menu Diagnostic Codes Menu From the Diagnostic Codes Menu View and write down the DTCs FromtheDiagnosticCodesMenu Select Erase Codes Ford Function List Ford Function List isOn Demand Test Menu With Mazda-sourced engines use the Mazda Electronic Control View Data From the Datastream Menu Select View Data Record Data Select data to viewFrom the Datastream Menu Select Record Data Ready to Record Diagnostic Codes Menu Read Koeo Codes Select Fast Codes or Slow CodesUse UP or Down arrow key until selection is highlighted When the test is complete Avoid cooling fan! It may turn on during test Return to Diagnostic Codes Menu. Press Back Read Koer CodesView and write down DTCs. Use UP or Down arrow key From the Diagnostic Codes Menu Select Read Koer Codes Key until Read Koer Codes isSelect Fast Codes, Slow Codes or Computed Timing When test completed 326 ENG Computed Timing Check 1984-1991 EEC-IV Vehicles From the Select Code Type menu Select Computed Timing Erase Codes EEC-IV Erase Codes Erase Memory Codes. Press Enter to begin erasing the codes Return to the Diagnostic Codes Menu. Press BackPerform the following 1 Turn ignition key off Mecs Erase Codes Follow all instructions on the display Select Read Koeo Codes. Use the UP or Down IVSC-Speed Ctrl EEC-IV VehiclesReading Ivsc Koeo Codes Perform the following 1Set parking brake When test is completed 568 Reading Ivsc Koer Codes Perform the following 37 ENG View and write down DTCs. Use the UP or Down arrow keys Wiggle Test EEC-IV Vehicles From the On Demand Test Menu Select Wiggle TestAfter making a selection Wiggle Test instructions Start KOEO/KOER Wiggle Test. Press EnterReturn to On Demand Test Output Switch Test EEC-IV Vehicles From the On Demand Test Menu Select Output Sw Test Perform the following 1 Set parking brake Toggle relays and solenoidsReturn to On Demand Test Menu Cylinder Cyl Balance Test EEC-IV Vehicles Wait for the Cylinder ID. Follow all user prompts Start Cyl Balance Test View test results Return to On Demand Test Menu. Press Back Star Test Mode EEC-IV, Mecs and MCU Vehicles From the On Demand Test Menu Return to the On Demand Test Menu. Press Back Three-Digit DTC 214 will Flash as follows Ford Enhanced OBD II Diagnostics Ford Function List is broken down into the following menus Review Data Print Data Read Codes From the Diagnostic Codes Menu Select Read Codes P1501 Trans Ford Diagnostics Chrysler Diagnostics Chrysler Function List Device Controls Menu Troubleshooting Datastream Menu View PIDs on Scan Tool. Use UP or Down arrow keys Use UP or Down arrow key until Record Data is highlighted Use UP or Down arrow key until Sensor Test is highlighted Sensor TestFrom the Datastream Menu Select Sensor Test Turn ignition key on Engine can be off or running Select Read Codes Keep hands and tools away from fan and engine during test P0406 ENG Follow the instructions. Press Enter Use UP or Down arrow key until Switch Test is highlighted Switch TestFrom the Device Controls Menu Select Switch Test Select switch to test. Use the UP or Down arrow key From the Device Controls Menu Select Actuator Test Operate selected switchActuator Test Use UP or Down arrow key until Actuator Test is highlighted Select Actuator to test. Use the UP or Down arrow key To test another actuator Press BackReturn to the Device Controls Menu Idle Speed Test During testReturn to the Device Controls Menu. Press Back Import Function List Import Function List is broken down into the following menus Exists, refer to Error Messages on Use UP or Down arrow key P0113 How to Use On-Line Help To Use On-Line Help Press Help KeyReturn to original screen Error Messages Scan Tool Does Not Power UpCheck the following if an error message displays Vehicle Communication Fault Turn vehicle key to off position Operating Error or Erroneous Data Remove Battery and Properly Discard Install New Battery Battery ReplacementRemove Battery Cover Reinstall Battery Cover Tool Self-Tests Technical Support Appendix a PID Definitions CLR TIM 0 65,535 min or 0 1092.25 hours Outsid AIR 40 215ºC or 40 419ºF Troub Code 0000 Ffff PID List 2ND Trip FT Desired AIR Pump Baro Calc ECT CCP Solenoid Cruise CYL 4 Misfire ECU RST-CLK L ENG TOR Evap VP Fault 3 KEY-ON FS/LR SOL Fuel SYS1 HI SPK Mode IAT Temp C/F INJ Fault Knock RET LO Coolant LMP Ltst DTC Pend MIS CYL P State O2 Sensorv O2S Bias ODM1 Ovrtemp Pres Torq REV Inhibit SET Sync Mode Spkadv CYL4 TCC Command THR POS C TR Switch C VEH Speed Appendix B Data Link Connectors GM Cars, Light Trucks & Vans Series Ford, Lincoln & Mercury Cars, Light Trucks & Vans Ford, Lincoln & Mercury Cars, Light Trucks & Vans SHP GVW Chrysler Cars, Light Trucks & Vans Chrysler Cars, Light Trucks & Vans Smec Data Link Connectors Pressure Sensor Pressure SwitchClutch Relay Actuator Catalytic Converter Brake Switch SignalBoost Control Solenoid Closed Loop CL Detonation Data Link Connector DLCData Stream Duty Cycle Freeze Frame Ground GNDHall Effect Sensor Knock Sensor KS Knock Mpfi or MFI MisfireMonitor NOx Relay Pending CodesPurge Solenoid Reluctance Sensor SFI or Sefi Scan ToolSensor Solenoid Throttle Body Traction AssistTrip Warm-up Cycle WOT Technical Service Repair SPX Corporation All Rights Reserved