Terminal Main Menu Navigating Within the Menus | ADTRAN T3SU 300

Chapter 2. Installation and Operation

2.Using the ADTRAN-provided terminal interface cable adapter, connect the DTE port of a terminal to the 8-pin modular jack labeled Control on the front panel of the T3SU 300.

3.Initialize the terminal session.

4.Press Enter repeatedly until the password prompt appears.

5.Enter the password. The factory default password is adtran. The MAIN menu appears. See Figure 2-3.

6.Make selections by entering the number corresponding to the chosen parameter. Press ESC to return to the previous screen. End a terminal session by selecting LOGOUT from the MAIN menu or by pressing Ctl-Cat any time.

Figure 2-3. Terminal Main Menu

Navigating Within the Menus

Navigate within the T3SU 300 terminal menus using the following procedures:

61200217L1-1

T3SU 300 User Manual

2-7

Image 29

ADTRAN T3SU 300 user manual Terminal Main Menu Navigating Within the Menus

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview Network Manager TelnetAgent MIB Card Interface Option CardsHssi Card Warranty and Customer Service Introduction 61200217L1-1 Adtran Shipments Include UNPACK, INSPECT, Power UPReceiving Inspection Rackmount Installation Installing the UnitPower Up Customer Provides Rear Panel Desktop Installation Function Alarm ConnectorDTE Port Interface Card Slots Auxiliary Port DTE Port 1 Hssi Interface DS3 Interface LAN PortFront Panel Control Port Terminal Main Menu Navigating Within the Menus Diagnostics ConfigurationRemote Login If you want to Press LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu DS3 Timing DS3 FramingLine Length DS3 Scrambler Remote Auto-ConfigurationData Link DTE Ports DTE Ports Menu Port Selections Active Port StatusInactive Not Installed ErrorApply Settings Waiting Off When OOS/OOF Idle When OffOff When Test Forced On Select Off When OOS/OOF or TestTransmit Clock Timed Profiles Screen Profiles 1 Timed Profiles Active Profile System ManagementProfile Time 1 Subnet Mask Local IP Address Gateway IP Address Auxiliary Port ModeRemote IP Address IP Security Read Community Name Modem ModeAuxiliary Port Baud Rate Trap Generation Write Community NameTrap IP Addresses Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions Toggle All Traps PasswordDTE Port Trap Description Alarm Relay Terminal TimeoutUnit ID Date/Time Dial String Initializing String Connection Timeout Idle TimeoutMaximum Redial Attempts Pause Between Calls Answer on Ring UtilitiesHangup Last Modem Response 11. System Utilities Menu If the self test results are Then Save Configuration Status Network Port Alarm StateNetwork State Condition Description Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type Hssi Interface Condition Leads BandwidthDTE Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Coding Violations CCV Bit Severely Errored Seconds PsesBit Coding Violations PCV Bit Errors MBE Bit Severely Errored Seconds CsesBit Errors FBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Bert DTE PortsRemote DS3 Loopback Remote Loopback with Bert Payload Bert Payload Loopback MUX DTE LoopbackMUX Bert OUT Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration Port Bert Information FieldsDirection State Insert Error ErrorsClear Errors Reset All Tests Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications Management DTESystem Multiport Application POINT-TO-POINT Multiport Application DTE 2 Hssi DTE 1 HssiDTE 3 DTE 4 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description Network Interface Specifications and FeaturesDTE Interfaces Integrated Hssi port DTE Rates Supported SNMP/Telnet VT 100 Terminal InterfaceAgency Approvals Environment Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 Ansi AISAMI BPV Bert Ccitt Control port Channel service unit See CSU ClockingCPE CSU DDS DCEDlci DS1 FDL FCC LOS LAN NRZ MIB SES POPPstn Telnet SnmpTDM WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Repair and Return Pre-Sales Inquiries and Applications SupportPost-Sale Support