Unit ID, Terminal Timeout, Date/Time, Alarm Relay | ADTRAN T3SU 300

Chapter 3. Configuration

Unit ID

Enter a name to identify the unit for management purposes.

Terminal Timeout

Set the amount of time the terminal or TELNET session can remain inactive before requiring re-entry of the password for access. This option can be disabled or set for 1 minute, 5 minutes, 15 minutes, 60 minutes, or one day.

Date/Time

Enter date and time information. Enter the time in military time (separated by colons). Enter the month, date, and year (separated by forward slashes). View this information in the STATISTICS menus.

Alarm Relay

Enable if the alarm terminal block (located on the rear of the unit) is connected to an audible alarm. If enabled, the alarm circuit is activated when a network alarm occurs.

Dialup Options

Configure the dialup capabilities of the T3SU 300. For product version 1200217L1, this option is only available if a dialup selection was made for the AUXILIARY PORT MODE (described on page 3-13). For product version 1200217L2, this option is always available. See Figure 3-10. Descriptions of the individual fields of this menu follow the figure.

61200217L1-1

T3SU 300 User Manual

3-19

Image 51

ADTRAN T3SU 300 user manual Unit ID, Terminal Timeout, Date/Time, Alarm Relay, Dialup Options

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview MIB TelnetNetwork Manager Agent Interface Option Cards Hssi CardCard Warranty and Customer Service Introduction 61200217L1-1 UNPACK, INSPECT, Power UP Receiving InspectionAdtran Shipments Include Customer Provides Installing the UnitRackmount Installation Power Up Rear Panel Desktop Installation Alarm Connector DTE Port Interface Card SlotsFunction Auxiliary Port DTE Port 1 Hssi Interface Control Port LAN PortDS3 Interface Front Panel Terminal Main Menu Navigating Within the Menus If you want to Press ConfigurationDiagnostics Remote Login LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu DS3 Framing Line LengthDS3 Timing DTE Ports Remote Auto-ConfigurationDS3 Scrambler Data Link DTE Ports Menu Port Selections Port Status InactiveActive Waiting ErrorNot Installed Apply Settings Forced On Idle When OffOff When OOS/OOF Off When Test Off When OOS/OOF or Test Transmit ClockSelect Timed Profiles Screen Profiles 1 Timed Profiles System Management Profile Time 1Active Profile Subnet Mask Local IP Address IP Security Auxiliary Port ModeGateway IP Address Remote IP Address Modem Mode Auxiliary Port Baud RateRead Community Name Write Community Name Trap IP AddressesTrap Generation Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions Password DTE Port Trap DescriptionToggle All Traps Date/Time Terminal TimeoutAlarm Relay Unit ID Dial String Initializing String Pause Between Calls Idle TimeoutConnection Timeout Maximum Redial Attempts Last Modem Response UtilitiesAnswer on Ring Hangup 11. System Utilities Menu If the self test results are Then Save Configuration Status Condition Description Alarm StateNetwork Port Network State Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type Bandwidth DTE LeadsHssi Interface Condition Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Severely Errored Seconds Pses Bit Coding Violations PCVBit Coding Violations CCV Bit Severely Errored Seconds Cses Bit Errors FBEBit Errors MBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Remote Loopback with Bert DTE PortsBert Remote DS3 Loopback Payload Bert Payload Loopback DTE Loopback MUX Bert OUTMUX Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration State Bert Information FieldsPort Direction Reset All Tests ErrorsInsert Error Clear Errors Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications DTE SystemManagement Multiport Application POINT-TO-POINT Multiport Application DTE 4 DTE 1 HssiDTE 2 Hssi DTE 3 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description DTE Rates Supported Specifications and FeaturesNetwork Interface DTE Interfaces Integrated Hssi port Environment VT 100 Terminal InterfaceSNMP/Telnet Agency Approvals Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 AIS AMIAnsi BPV Bert Ccitt CSU Channel service unit See CSU ClockingControl port CPE DS1 DCEDDS Dlci FDL FCC LOS LAN NRZ MIB POP PstnSES Snmp TDMTelnet WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Pre-Sales Inquiries and Applications Support Post-Sale SupportRepair and Return