Timed Profiles Screen Profiles 1 | ADTRAN T3SU 300 specification

Chapter 3. Configuration

Selecting Normal or Invert clocking options depends on your DTE, cable length, and cable characteristics. To verify error free operation, perform a DTE loopback test and a BERT test from the DTE. See the chapter Diag- nostics on page 6-1 for information on performing these tests.

Timed Profiles

Using this option, you can allocate bandwidth based on the time of day. For example, you can assign more bandwidth to the corporate LAN during business hours and more bandwidth to a backup machine in the evenings. The T3SU 300 can store two separate user profiles which have bandwidth selections for each of the four ports. See Figure 3-5and Figure 3-6.

Figure 3-5. Timed Profiles Screen

Profiles 1 and 2

The PROFILE CONFIGURATION screens allow you to change the PORT STATE and NX75K BLOCKS options for all four ports. See page 3-7 for descriptions of these options. The settings are then assigned to

3-10

T3SU 300 User Manual

61200217L1-1

Image 42

ADTRAN T3SU 300 user manual Timed Profiles Screen Profiles 1

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Introduction Product Overview T3 Overview Snmp Agent TelnetNetwork Manager MIB Interface Option Cards Hssi CardCard Warranty and Customer Service Introduction 61200217L1-1 UNPACK, INSPECT, Power UP Receiving InspectionAdtran Shipments Include Power Up Installing the UnitRackmount Installation Customer Provides Desktop Installation Rear Panel Alarm Connector DTE Port Interface Card SlotsFunction DTE Port 1 Hssi Interface Auxiliary Port Front Panel LAN PortDS3 Interface Control Port Terminal Main Menu Navigating Within the Menus Remote Login ConfigurationDiagnostics If you want to Press LED Descriptions LOS LED Condition Configuration DTE Ports Configuration Main Menu DS3 Network DS3 Framing Line LengthDS3 Timing Data Link Remote Auto-ConfigurationDS3 Scrambler DTE Ports Port Selections DTE Ports Menu Port Status InactiveActive Apply Settings ErrorNot Installed Waiting Off When Test Idle When OffOff When OOS/OOF Forced On Off When OOS/OOF or Test Transmit ClockSelect Timed Profiles Timed Profiles Screen Profiles 1 System Management Profile Time 1Active Profile Local IP Address Subnet Mask Remote IP Address Auxiliary Port ModeGateway IP Address IP Security Modem Mode Auxiliary Port Baud RateRead Community Name Write Community Name Trap IP AddressesTrap Generation Far End Alarm Trap Descriptions Trap Type If ENABLED, this trap is sent MIB II Standard Trap Descriptions Network Test Trap Descriptions Password DTE Port Trap DescriptionToggle All Traps Unit ID Terminal TimeoutAlarm Relay Date/Time Initializing String Dial String Maximum Redial Attempts Idle TimeoutConnection Timeout Pause Between Calls Hangup UtilitiesAnswer on Ring Last Modem Response If the self test results are Then 11. System Utilities Menu Save Configuration Status Network State Alarm StateNetwork Port Condition Description Data Link State Remote State Com Eqpt Fail Network has signaled a non-service affecting Interface Type Port Status Bandwidth DTE LeadsHssi Interface Condition Leads LA and LB Leads Condition Interface Leads Status 61200217L1-1 Viewing Statistical Information Alarm History Main Local Statistics Menu Screen Current Alarm Count Screen Performance Parameters Bit Severely Errored Seconds Pses Bit Coding Violations PCVBit Coding Violations CCV Bit Severely Errored Seconds Cses Bit Errors FBEBit Errors MBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics Diagnostics Main Menu DS3 DS3 Diagnostics Menu Data Mode DS3 Payload Loopback DTE Remote DS3 Loopback DTE PortsBert Remote Loopback with Bert Payload Loopback Payload Bert DTE Loopback MUX Bert OUTMUX Payload and DTE Loopback Remote Payload Loopback with Bert Bert Configuration Pattern Direction Bert Information FieldsPort State Clear Errors ErrorsInsert Error Reset All Tests Diagnostics 61200217L1-1 Applications Single Port Full T3 Bandwidth DTE SystemManagement POINT-TO-POINT Multiport Application Multiport Application DTE 3 DTE 1 HssiDTE 2 Hssi DTE 4 Fractional T3 Carrier Application Fractional Application Hssi Local Remote Remote Snmp Management Application Remote Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Table A-3. V.35 Interface Card Pin Assignments Ccitt Table A-4. LAN Port Pin Assignments Name Description TD+ DTE Interfaces Integrated Hssi port Specifications and FeaturesNetwork Interface DTE Rates Supported Agency Approvals VT 100 Terminal InterfaceSNMP/Telnet Environment Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 AIS AMIAnsi Bert BPV Ccitt CPE Channel service unit See CSU ClockingControl port CSU Dlci DCEDDS DS1 FCC FDL LAN LOS MIB NRZ POP PstnSES Snmp TDMTelnet Yellow alarm WAN Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Pre-Sales Inquiries and Applications Support Post-Sale SupportRepair and Return