MIB II Standard Trap Descriptions | ADTRAN T3SU 300 guide

				Chapter 3. Configuration

		Trap Type		If ENABLED, this trap is sent...

		Idle Signal		when the unit receives indication from the far
				end unit through the FEAC channel that the far
				end unit is receiving an idle signal (1100) over
				the entire DS3 payload.

		Eqpt. Fail		when the unit receives indication from the net-
		NSA		work through the FEAC channel of a non-ser-
				vice-affecting failure in the network equipment.

		Eqpt. Fail SA		when the unit receives indication from the net-
				work through the FEAC channel of a service-af-
				fecting failure in the network equipment.

		Com. Eqpt.		when the unit receives indication from the net-
		Fail NSA		work through the FEAC channel of a non-ser-
				vice-affecting failure in the network common
				equipment.

		Table 3-3. MIB II Standard Trap Descriptions

	Trap Type		If ENABLED, this trap is sent...

	Cold Start		when the unit is first powered on.

	Link Up		when the network recovers from a Link Down con-
			dition and data transmission is restored.

	Link Down		when a network condition prevents data transmis-
			sion. This could be either an alarm or a network
			test.

	Auth. Failure		when an SNMP request is made with the wrong
			read or write community names.

			Table 3-4. Network Test Trap Descriptions

	Trap Type		If ENABLED, this trap is sent...

	Network Test In		when the unit goes into a DS3 network test, either
			commanded locally or remotely.

	Network Test		when the unit is in a DS3 network test and the test
	Out		is terminated.

61200217L1-1

T3SU 300 User Manual

3-17

Image 49

ADTRAN T3SU 300 user manual MIB II Standard Trap Descriptions, Network Test Trap Descriptions

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview Network Manager TelnetAgent MIB Hssi Card Interface Option CardsCard Warranty and Customer Service Introduction 61200217L1-1 Receiving Inspection UNPACK, INSPECT, Power UPAdtran Shipments Include Rackmount Installation Installing the UnitPower Up Customer Provides Rear Panel Desktop Installation DTE Port Interface Card Slots Alarm ConnectorFunction Auxiliary Port DTE Port 1 Hssi Interface DS3 Interface LAN PortFront Panel Control Port Terminal Main Menu Navigating Within the Menus Diagnostics ConfigurationRemote Login If you want to Press LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu Line Length DS3 FramingDS3 Timing DS3 Scrambler Remote Auto-ConfigurationData Link DTE Ports DTE Ports Menu Port Selections Inactive Port StatusActive Not Installed ErrorApply Settings Waiting Off When OOS/OOF Idle When OffOff When Test Forced On Transmit Clock Off When OOS/OOF or TestSelect Timed Profiles Screen Profiles 1 Timed Profiles Profile Time 1 System ManagementActive Profile Subnet Mask Local IP Address Gateway IP Address Auxiliary Port ModeRemote IP Address IP Security Auxiliary Port Baud Rate Modem ModeRead Community Name Trap IP Addresses Write Community NameTrap Generation Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions DTE Port Trap Description PasswordToggle All Traps Alarm Relay Terminal TimeoutUnit ID Date/Time Dial String Initializing String Connection Timeout Idle TimeoutMaximum Redial Attempts Pause Between Calls Answer on Ring UtilitiesHangup Last Modem Response 11. System Utilities Menu If the self test results are Then Save Configuration Status Network Port Alarm StateNetwork State Condition Description Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type DTE Leads BandwidthHssi Interface Condition Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Coding Violations PCV Bit Severely Errored Seconds PsesBit Coding Violations CCV Bit Errors FBE Bit Severely Errored Seconds CsesBit Errors MBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Bert DTE PortsRemote DS3 Loopback Remote Loopback with Bert Payload Bert Payload Loopback MUX Bert OUT DTE LoopbackMUX Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration Port Bert Information FieldsDirection State Insert Error ErrorsClear Errors Reset All Tests Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications System DTEManagement Multiport Application POINT-TO-POINT Multiport Application DTE 2 Hssi DTE 1 HssiDTE 3 DTE 4 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description Network Interface Specifications and FeaturesDTE Interfaces Integrated Hssi port DTE Rates Supported SNMP/Telnet VT 100 Terminal InterfaceAgency Approvals Environment Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 AMI AISAnsi BPV Bert Ccitt Control port Channel service unit See CSU ClockingCPE CSU DDS DCEDlci DS1 FDL FCC LOS LAN NRZ MIB Pstn POPSES TDM SnmpTelnet WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Post-Sale Support Pre-Sales Inquiries and Applications SupportRepair and Return