Maximum Redial Attempts, Idle Timeout | ADTRAN T3SU 300 specs

Chapter 3. Configuration

Maximum Redial Attempts

The T3SU 300 attempts to establish a call the number of times entered in this field. If a successful call is not established after the final attempt, the T3SU 300 discards the trap messages.

Idle Timeout

Once a call is established and the trap messages are sent, the T3SU 300 remains online for the amount of seconds entered in this field. If the field is set to 0, the unit hangs up as soon as the trap is sent.

Connection Timeout

The T3SU 300 waits for a connection the amount of seconds entered in this field. Timing begins as soon as the dial command is issued.

Pause Between Calls

The T3SU 300 waits the number of seconds entered in this field between redial attempts.

Dialout On Trap

Enable or disable the T3SU 300’s ability to dial out to report traps. When the AUXILIARY PORT MODE (product version 1200217L1) or MODEM MODE (product version 1200217L2) is configured for DIALUP VT 100, the unit reports error conditions in plain ASCII with the following information:

•The Unit ID value programmed in the Unit ID field of the second SYSTEM MANAGEMENT screen (see Figure 3-9)

•A trap code indicating the error condition (selected from the

TRAP GENERATION screen under SYSTEM MANAGEMENT)

•The date and time when the error was logged

When the AUXILIARY PORT MODE or MODEM MODE is configured for DIALUP PPP or DIALUP SLIP, the unit logs in to the PPP/SLIP host and reports the error conditions to the hosts designated under the

TRAP IP ADDRESSES (also found under SYSTEM MANAGEMENT).

61200217L1-1

T3SU 300 User Manual

3-21

Image 53

ADTRAN T3SU 300 user manual Maximum Redial Attempts, Idle Timeout, Connection Timeout, Pause Between Calls, Dialout On Trap

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview Network Manager TelnetAgent MIB Card Interface Option CardsHssi Card Warranty and Customer Service Introduction 61200217L1-1 Adtran Shipments Include UNPACK, INSPECT, Power UPReceiving Inspection Rackmount Installation Installing the UnitPower Up Customer Provides Rear Panel Desktop Installation Function Alarm ConnectorDTE Port Interface Card Slots Auxiliary Port DTE Port 1 Hssi Interface DS3 Interface LAN PortFront Panel Control Port Terminal Main Menu Navigating Within the Menus Diagnostics ConfigurationRemote Login If you want to Press LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu DS3 Timing DS3 FramingLine Length DS3 Scrambler Remote Auto-ConfigurationData Link DTE Ports DTE Ports Menu Port Selections Active Port StatusInactive Not Installed ErrorApply Settings Waiting Off When OOS/OOF Idle When OffOff When Test Forced On Select Off When OOS/OOF or TestTransmit Clock Timed Profiles Screen Profiles 1 Timed Profiles Active Profile System ManagementProfile Time 1 Subnet Mask Local IP Address Gateway IP Address Auxiliary Port ModeRemote IP Address IP Security Read Community Name Modem ModeAuxiliary Port Baud Rate Trap Generation Write Community NameTrap IP Addresses Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions Toggle All Traps PasswordDTE Port Trap Description Alarm Relay Terminal TimeoutUnit ID Date/Time Dial String Initializing String Connection Timeout Idle TimeoutMaximum Redial Attempts Pause Between Calls Answer on Ring UtilitiesHangup Last Modem Response 11. System Utilities Menu If the self test results are Then Save Configuration Status Network Port Alarm StateNetwork State Condition Description Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type Hssi Interface Condition Leads BandwidthDTE Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Coding Violations CCV Bit Severely Errored Seconds PsesBit Coding Violations PCV Bit Errors MBE Bit Severely Errored Seconds CsesBit Errors FBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Bert DTE PortsRemote DS3 Loopback Remote Loopback with Bert Payload Bert Payload Loopback MUX DTE LoopbackMUX Bert OUT Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration Port Bert Information FieldsDirection State Insert Error ErrorsClear Errors Reset All Tests Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications Management DTESystem Multiport Application POINT-TO-POINT Multiport Application DTE 2 Hssi DTE 1 HssiDTE 3 DTE 4 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description Network Interface Specifications and FeaturesDTE Interfaces Integrated Hssi port DTE Rates Supported SNMP/Telnet VT 100 Terminal InterfaceAgency Approvals Environment Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 Ansi AISAMI BPV Bert Ccitt Control port Channel service unit See CSU ClockingCPE CSU DDS DCEDlci DS1 FDL FCC LOS LAN NRZ MIB SES POPPstn Telnet SnmpTDM WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Repair and Return Pre-Sales Inquiries and Applications SupportPost-Sale Support