Data Link State, Remote State | ADTRAN T3SU 300 guide

		Chapter 4. Status

	Condition	Description

	Blue (AIS)	The unit is receiving a blue alarm condition from
		the network. A blue alarm occurs when consecu-
		tive 1010s are received in the information bits.
		This indicates that there is a transmission fault lo-
		cated either at or upstream from the transmitting
		terminal.

	OOF	The unit detects an out of frame condition from the
		network.

	Idle	The unit detects an idle sequence from the net-
		work. Service is immediately available for use.

Data Link State

This field displays the current state of the data link between the local and the remote T3SU 300s. Possible states are listed in the following table:

Condition	Description

Normal	The local unit’s data link is in sync with the remote
	unit.

Disabled	The DATA LINK option in the DS3 NETWORK
	CONFIGURATION menu is set to DISABLED.

Down	The local and remote units are not in sync.

Remote State

This field displays the current state of the remote link. Possible states are listed in the following table:

61200217L1-1

T3SU 300 User Manual

4-3

Image 59

ADTRAN T3SU 300 user manual Data Link State, Remote State

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview MIB TelnetNetwork Manager Agent Card Interface Option CardsHssi Card Warranty and Customer Service Introduction 61200217L1-1 Adtran Shipments Include UNPACK, INSPECT, Power UPReceiving Inspection Customer Provides Installing the UnitRackmount Installation Power Up Rear Panel Desktop Installation Function Alarm ConnectorDTE Port Interface Card Slots Auxiliary Port DTE Port 1 Hssi Interface Control Port LAN PortDS3 Interface Front Panel Terminal Main Menu Navigating Within the Menus If you want to Press ConfigurationDiagnostics Remote Login LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu DS3 Timing DS3 FramingLine Length DTE Ports Remote Auto-ConfigurationDS3 Scrambler Data Link DTE Ports Menu Port Selections Active Port StatusInactive Waiting ErrorNot Installed Apply Settings Forced On Idle When OffOff When OOS/OOF Off When Test Select Off When OOS/OOF or TestTransmit Clock Timed Profiles Screen Profiles 1 Timed Profiles Active Profile System ManagementProfile Time 1 Subnet Mask Local IP Address IP Security Auxiliary Port ModeGateway IP Address Remote IP Address Read Community Name Modem ModeAuxiliary Port Baud Rate Trap Generation Write Community NameTrap IP Addresses Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions Toggle All Traps PasswordDTE Port Trap Description Date/Time Terminal TimeoutAlarm Relay Unit ID Dial String Initializing String Pause Between Calls Idle TimeoutConnection Timeout Maximum Redial Attempts Last Modem Response UtilitiesAnswer on Ring Hangup 11. System Utilities Menu If the self test results are Then Save Configuration Status Condition Description Alarm StateNetwork Port Network State Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type Hssi Interface Condition Leads BandwidthDTE Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Coding Violations CCV Bit Severely Errored Seconds PsesBit Coding Violations PCV Bit Errors MBE Bit Severely Errored Seconds CsesBit Errors FBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Remote Loopback with Bert DTE PortsBert Remote DS3 Loopback Payload Bert Payload Loopback MUX DTE LoopbackMUX Bert OUT Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration State Bert Information FieldsPort Direction Reset All Tests ErrorsInsert Error Clear Errors Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications Management DTESystem Multiport Application POINT-TO-POINT Multiport Application DTE 4 DTE 1 HssiDTE 2 Hssi DTE 3 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description DTE Rates Supported Specifications and FeaturesNetwork Interface DTE Interfaces Integrated Hssi port Environment VT 100 Terminal InterfaceSNMP/Telnet Agency Approvals Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 Ansi AISAMI BPV Bert Ccitt CSU Channel service unit See CSU ClockingControl port CPE DS1 DCEDDS Dlci FDL FCC LOS LAN NRZ MIB SES POPPstn Telnet SnmpTDM WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Repair and Return Pre-Sales Inquiries and Applications SupportPost-Sale Support