DS3 Framing, Line Length, DS3 Timing | ADTRAN T3SU 300 manual

Chapter 3. Configuration

Figure 3-2. DS3 Network Configuration Menu

DS3 Framing

Set the framing format to match the format of the receive signal at the network interface. C-bit parity and M13 framing formats are supported.

Line Length

Set the line length to reflect the physical length of the DS3 network line. Set to LONG if the cabling distance exceeds 50 feet; set to SHORT if the distance is less than 50 feet.

DS3 Timing

Set the timing to LOOP if the T3SU 300 is to derive timing from the network; set to LOCAL if the unit is to be the master timing source for the circuit. In most cases, the unit should be configured for LOOP timing.

61200217L1-1

T3SU 300 User Manual

3-3

Image 35

ADTRAN T3SU 300 user manual DS3 Framing, Line Length, DS3 Timing

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Product Overview Introduction Snmp T3 Overview MIB TelnetNetwork Manager Agent Card Interface Option CardsHssi Card Warranty and Customer Service Introduction 61200217L1-1 Adtran Shipments Include UNPACK, INSPECT, Power UPReceiving Inspection Customer Provides Installing the UnitRackmount Installation Power Up Rear Panel Desktop Installation Function Alarm ConnectorDTE Port Interface Card Slots Auxiliary Port DTE Port 1 Hssi Interface Control Port LAN PortDS3 Interface Front Panel Terminal Main Menu Navigating Within the Menus If you want to Press ConfigurationDiagnostics Remote Login LOS LED Descriptions Condition LED DTE Ports Configuration DS3 Network Configuration Main Menu DS3 Timing DS3 FramingLine Length DTE Ports Remote Auto-ConfigurationDS3 Scrambler Data Link DTE Ports Menu Port Selections Active Port StatusInactive Waiting ErrorNot Installed Apply Settings Forced On Idle When OffOff When OOS/OOF Off When Test Select Off When OOS/OOF or TestTransmit Clock Timed Profiles Screen Profiles 1 Timed Profiles Active Profile System ManagementProfile Time 1 Subnet Mask Local IP Address IP Security Auxiliary Port ModeGateway IP Address Remote IP Address Read Community Name Modem ModeAuxiliary Port Baud Rate Trap Generation Write Community NameTrap IP Addresses Trap Type If ENABLED, this trap is sent Far End Alarm Trap Descriptions Network Test Trap Descriptions MIB II Standard Trap Descriptions Toggle All Traps PasswordDTE Port Trap Description Date/Time Terminal TimeoutAlarm Relay Unit ID Dial String Initializing String Pause Between Calls Idle TimeoutConnection Timeout Maximum Redial Attempts Last Modem Response UtilitiesAnswer on Ring Hangup 11. System Utilities Menu If the self test results are Then Save Configuration Status Condition Description Alarm StateNetwork Port Network State Remote State Data Link State Com Eqpt Fail Network has signaled a non-service affecting Port Status Interface Type Hssi Interface Condition Leads BandwidthDTE Leads Interface Leads LA and LB Leads Condition Status 61200217L1-1 Viewing Statistical Information Main Local Statistics Menu Screen Alarm History Current Alarm Count Screen Performance Parameters Bit Coding Violations CCV Bit Severely Errored Seconds PsesBit Coding Violations PCV Bit Errors MBE Bit Severely Errored Seconds CsesBit Errors FBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics DS3 Diagnostics Main Menu DS3 Payload Loopback DS3 Diagnostics Menu Data Mode DTE Remote Loopback with Bert DTE PortsBert Remote DS3 Loopback Payload Bert Payload Loopback MUX DTE LoopbackMUX Bert OUT Remote Payload Loopback with Bert Payload and DTE Loopback Pattern Bert Configuration State Bert Information FieldsPort Direction Reset All Tests ErrorsInsert Error Clear Errors Diagnostics 61200217L1-1 Single Port Full T3 Bandwidth Applications Management DTESystem Multiport Application POINT-TO-POINT Multiport Application DTE 4 DTE 1 HssiDTE 2 Hssi DTE 3 Fractional Application Fractional T3 Carrier Application Remote Hssi Local Remote Management Application Remote Snmp Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Ccitt Table A-3. V.35 Interface Card Pin Assignments TD+ Table A-4. LAN Port Pin Assignments Name Description DTE Rates Supported Specifications and FeaturesNetwork Interface DTE Interfaces Integrated Hssi port Environment VT 100 Terminal InterfaceSNMP/Telnet Agency Approvals Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 Ansi AISAMI BPV Bert Ccitt CSU Channel service unit See CSU ClockingControl port CPE DS1 DCEDDS Dlci FDL FCC LOS LAN NRZ MIB SES POPPstn Telnet SnmpTDM WAN Yellow alarm Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Repair and Return Pre-Sales Inquiries and Applications SupportPost-Sale Support