ADTRAN T3SU 300 manual

Chapter 4. Status

Condition	Description

Normal	No alarms are currently being received.

RAI (Yellow	The unit is transmitting a yellow alarm from the
Alarm)	network. This alarm is a signal sent back toward
	the source of a failed transmit circuit. The X-bits
	(X1 and X2) are set to zero.

LOS (Red	The unit has lost the Rx signal.
Alarm)

AIS (Blue	The unit is receiving a blue alarm condition from
Alarm)	the network. A blue alarm occurs when consecu-
	tive 1010s are received in the information bits.
	This indicates that there is a transmission fault lo-
	cated either at or upstream from the transmitting
	terminal.

OOF	The unit detects an out of frame condition from the
	network.

Idle	The unit detects an idle sequence from the net-
	work. Service is immediately available for use.

Eqpt Fail (SA)	The network has signaled a service affecting
	equipment failure condition.

Eqpt Fail	The network has signaled a non-service affecting
(NSA)	equipment failure condition.

Com Eqpt Fail	The network has signaled a non-service affecting
(NSA)	common equipment failure condition.

Unknown	The T3SU 300 is unable to determine the state of
	the network or the remote unit.

4-4

T3SU 300 User Manual

61200217L1-1

Image 60

ADTRAN T3SU 300 user manual Com Eqpt Fail Network has signaled a non-service affecting

Contents

T3SU Trademark Information About this Manual Important Safety Instructions REN FIC Usoc Year 2000 Compliance Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Status Appendix C. Acronyms/Abbreviations Appendix D. Glossary Table of Contents Xii 61200217L1-1 List of Figures Line Loopback Test List of Tables List of Tables Xvi 61200217L1-1 Introduction Product Overview T3 Overview Snmp Telnet Network ManagerAgent MIB Interface Option Cards Hssi CardCard Warranty and Customer Service Introduction 61200217L1-1 UNPACK, INSPECT, Power UP Receiving InspectionAdtran Shipments Include Installing the Unit Rackmount InstallationPower Up Customer Provides Desktop Installation Rear Panel Alarm Connector DTE Port Interface Card SlotsFunction DTE Port 1 Hssi Interface Auxiliary Port LAN Port DS3 InterfaceFront Panel Control Port Terminal Main Menu Navigating Within the Menus Configuration DiagnosticsRemote Login If you want to Press LED Descriptions LOS LED Condition Configuration DTE Ports Configuration Main Menu DS3 Network DS3 Framing Line LengthDS3 Timing Remote Auto-Configuration DS3 ScramblerData Link DTE Ports Port Selections DTE Ports Menu Port Status InactiveActive Error Not InstalledApply Settings Waiting Idle When Off Off When OOS/OOFOff When Test Forced On Off When OOS/OOF or Test Transmit ClockSelect Timed Profiles Timed Profiles Screen Profiles 1 System Management Profile Time 1Active Profile Local IP Address Subnet Mask Auxiliary Port Mode Gateway IP AddressRemote IP Address IP Security Modem Mode Auxiliary Port Baud RateRead Community Name Write Community Name Trap IP AddressesTrap Generation Far End Alarm Trap Descriptions Trap Type If ENABLED, this trap is sent MIB II Standard Trap Descriptions Network Test Trap Descriptions Password DTE Port Trap DescriptionToggle All Traps Terminal Timeout Alarm RelayUnit ID Date/Time Initializing String Dial String Idle Timeout Connection TimeoutMaximum Redial Attempts Pause Between Calls Utilities Answer on RingHangup Last Modem Response If the self test results are Then 11. System Utilities Menu Save Configuration Status Alarm State Network PortNetwork State Condition Description Data Link State Remote State Com Eqpt Fail Network has signaled a non-service affecting Interface Type Port Status Bandwidth DTE LeadsHssi Interface Condition Leads LA and LB Leads Condition Interface Leads Status 61200217L1-1 Viewing Statistical Information Alarm History Main Local Statistics Menu Screen Current Alarm Count Screen Performance Parameters Bit Severely Errored Seconds Pses Bit Coding Violations PCVBit Coding Violations CCV Bit Severely Errored Seconds Cses Bit Errors FBEBit Errors MBE All statistical information not just the displayed screen Statistics 61200217L1-1 Diagnostics Diagnostics Main Menu DS3 DS3 Diagnostics Menu Data Mode DS3 Payload Loopback DTE DTE Ports BertRemote DS3 Loopback Remote Loopback with Bert Payload Loopback Payload Bert DTE Loopback MUX Bert OUTMUX Payload and DTE Loopback Remote Payload Loopback with Bert Bert Configuration Pattern Bert Information Fields PortDirection State Errors Insert ErrorClear Errors Reset All Tests Diagnostics 61200217L1-1 Applications Single Port Full T3 Bandwidth DTE SystemManagement POINT-TO-POINT Multiport Application Multiport Application DTE 1 Hssi DTE 2 HssiDTE 3 DTE 4 Fractional T3 Carrier Application Fractional Application Hssi Local Remote Remote Snmp Management Application Remote Management Application Datalink = Enabled Appendix a Pinouts Signal Ground SG Table A-3. V.35 Interface Card Pin Assignments Ccitt Table A-4. LAN Port Pin Assignments Name Description TD+ Specifications and Features Network InterfaceDTE Interfaces Integrated Hssi port DTE Rates Supported VT 100 Terminal Interface SNMP/TelnetAgency Approvals Environment Appendix C Acronyms/Abbreviations DDS OOF Appendix C. Acronyms/Abbreviations 61200217L1-1 AIS AMIAnsi Bert BPV Ccitt Channel service unit See CSU Clocking Control portCPE CSU DCE DDSDlci DS1 FCC FDL LAN LOS MIB NRZ POP PstnSES Snmp TDMTelnet Yellow alarm WAN Appendix D. Glossary 61200217L1-1 Index DS3 Index-3 Index-4 61200217L1-1 Index-5 Yellow alarm traps Pre-Sales Inquiries and Applications Support Post-Sale SupportRepair and Return