From, 108 | Agilent Technologies AGILENT MODELS 6023A and 6028A

6023A	In the parts list for the Chassis Mechanical change the following:
		FROM	TO
	Cover-top	06023-00020	06023-00002
	Cover bottom	06023-00022	06023-00003
	Trim top	5041-8803	5040-7203
	Trim sides	5001-0540	5001-0440
	Front Frame	5021-8417	5021-5817
	Feet	5041-8801	5040-7201
	Strap Handle Assy	5062-3703	5060-9803
	Strap Retain Rear	5041-8820	5041-6820
	Strap Retain Front	5041-8819	5041-6819

CHANGE 6

6023A	In the parts list for the Appendix A delete resistor R57 .49K 1%, 1/8W p/n 0698-3226 and solder
	pin p/n 0360-1300.

CHANGE 7

6023A	In the parts list for the A2 Control Board Assembly delete R152, 1K 1/4W, R155, R158, 0 ohms
	p/n 8159-0005.

CHANGE 8

6023A	In the parts list for the Chassis Mechanical change the following:
		FROM	TO
	Retainer Strap Handle	5041-6819	5040-7219
	Retainer Strap Handle	5041-6820	5040-7220
	Chassis	06023-00016	06023-00001
	Rear panel screened	06023-00019	06023-00011
	Front Frame	5021-5817	5020-8817
	Delete sub panel, front p/n 06023-00018

CHANGE 9

6023A	In the parts list for the A3 Front-Panel Board Assembly change DS1, DS5 to p/n 1990-0681,
	DS2-DS4, DS6-DS8 to p/n 1990-0050.

CHANGE 10

6023A	In the parts list for the Chassis change panel sub from 06023-00014 to 06023-0006, change front-
	panel from 06023-00015 to 06023-00012.

108

Image 108

Agilent Technologies AGILENT MODELS 6023A and 6028A service manual From, 108

Contents

Autoranging Certification Safety Summary Safety Symbol Definitions Printing History Table of Contents Replaceable Parts Troubleshooting Circuit DiagramsSafety Considerations Scope Manual Revisions Item Description Calibration Procedure IntroductionTest Equipment Required Operation Verification Tests Type Required Characteristics USE Recommended Model Test Equipment Required Initial Setup 1KVA Calibration Procedure MON Vout Iout Performance Tests Measurement TechniquesCR7 Current-Monitoring Resistor Setup Constant Voltage CV Tests Basic Test Setup RMS Measurement Test Setup, CV Pard Test Peak-To-Peak Measurement Test Setup, CV Pard Test 6023A 6028A KHz Noise, CV Peak-to-Peak Pard Load Transient Recovery Waveform Constant Current CC Tests CC Pard Test Setup Troubleshooting Initial Troubleshooting Procedures Control Board Test Connector, A2J7 PIN no Signal NameVdc WAVEFORM/CONDITIONS Source Repair and Replacement Electrostatic Protection A2 Control Board Removal A4 Power Mesh Board Removal Overall Troubleshooting ProcedureA3 Front-Panel Board Removal A1 Main Board Removal Using the Tables SetupNode Measurement Main Troubleshooting Setup Main Troubleshooting Setup Modified Mains Cord Set For Troubleshooting Troubleshooting No-Output Failures Front-Panel Troubleshooting PWM-ON PWM-OFF Defective Check Functional Circuits A2J7-26 A2J7-25Board Troubleshooting Bias Supplies Symptoms Defective Circuit Check ComponentsSymptoms Defective Check Functional Circuits Board Node + Measurement Source Node + Measurement SourceNode + N0DE Power Section Blocks Troubleshooting AC-Turn-on CircuitsSetup Measurement Source Setup Measurement Troubleshooting PWM & Clock Relay EnablePower Limit Troubleshooting DC-To-DC Converter + OUTPWM-ON PWM-OFF Troubleshooting CV Circuit Troubleshooting CC Circuit Troubleshooting Down Programmer Troubleshooting OVP CircuitA4U4OUT Waveforms SET Voltage Vdc Node + Page Autoranging Power Block Diagram Overview Block Diagram Simplified Schematic Simplified Schematic DC-to-DC Converter Down Programmer Pfet Control Signals Timing Diagram Constant-Voltage CV Circuit Power-Limit Comparator Constant-Current CC CircuitOvervoltage Protection OVP Circuit Control-Voltage Comparator Initial-Ramp Circuit Pulse-Width Modulator PWMBias Voltage Detector AC-Surge Dropout Detector Second-Delay Circuit Display CircuitsPage Replaceable Parts Reference Designators Ordering Information Description Abbreviations Electrical Parts CR1CR2 CR3 XA2P1 XA2P2Mechanical Parts Control Board Assembly CR3 Page Page Page VR3 VR4VR5 CR5 DS1DS5 IC A/D Cmos 3-1/2 DGT VR1VR2 NPN SI Pfet TS1 Chassis Electrical A1TB1 A2 Board Mechanical PartsA3 Board Mechanical Parts A4 Board Mechanical Parts Option 220 220V Operation Option 240 240V Operation Component Location and Circuit Diagrams Schematic Diagram Notes Pin locations for other semi-conductors are shown below Top View, Top Covers Removed Main Board A1 Component Location Control Board A2 Component Location Front-Panel Board A3 Component Location Power Mesh Board A4 Component Location Page Page Specifications General InformationOption 002 Hardware Table A-1. Specifications, Option Remote Programming Input Compliance Voltage ± Current Programming EnableOutput Impedance 10.2 k ohm ± 5% Temperature Coefficient Status Indicators Remote Trip and Remote Reset Timing Power-on PresetMaximum Output Voltage logic high + On State logic low Table A-1. Specifications, Option Pulse Timing Bias Supplies DC Output Ratings 25C ±Short Circuit Output Current Pard Typical Installation Connector Assembly Procedure Figure A-1. Mating Connector Assembly Operation Local/Remote Programming Resistance Voltage or Current Remote Resistance Programming Figure A-4. Calculating Value of Series Dropping Resistor Figure A-5. Remote Resistance Programming Remote Monitoring Status Indicators Remote Control Remote Reset Overvoltage Power-On Preset Figure A-8. Remote Control AC Dropout Buffer Circuit Multiple Supply System Shutdown Maintenance Bias Supplies Troubleshooting Resistance and Voltage Programming Troubleshooting Current Programming Figure A-11. Troubleshooting Current Programming of CV Mode Figure A-13. Troubleshooting Status Indicators Page Table A-3. Replacement Parts REF. Desig Model no Description 100 VR9 101 Indicator and Qualifier Symbols OLD Symbol NEW SymbolLogic Symbols and Definitions 102 Definitions Schematic Notes Schematic Diagram Notes 103 Schematic Notes Figure A-15. Option 002 Board, Component Location 104 Figure A-16. Option 002 Board, Schematic Diagram 105 Page Model 6023A Model 6028A107 From 108