Scope | Agilent Technologies AGILENT MODELS 6023A and 6028A specification

1

Introduction

Scope

This manual contains information for troubleshooting the Agilent 6023A or 6028A 200W Autoranging Power Supply to the component level. Wherever applicable, the service instructions given in this manual refer to pertinent information provided in the Operation Manual. Both manuals cover Agilent Models 6023A/28A; differences between models are described as required.

The following information is contained in this manual.

Calibration and Verification

Contains calibration procedures for Agilent Models 6023A/28A. Also contains verification procedures that check the operation of the supplies to ensure they meet the specifications of Chapter 1 in the Operating Manual.

Troubleshooting

Contains troubleshooting procedures to isolate a malfunction to a defective component on the main circuit board or to a defective assembly (front-panel, power transformer, or cable assembly). Board and assembly level removal and replacement procedures are also given in this section.

Principles of Operation

Provides block diagram level descriptions of the supply's circuits. The regulation & control, protection, input power, dc power conversion and output circuits are described. These descriptions are intended as an aid in troubleshooting.

Replaceable Parts

Provides a listing of replaceable parts for all electronic components and mechanical assemblies for Agilent Models 6023A/28A.

Circuit Diagrams

Contains functional schematics and component location diagrams for all Agilent 6023A/28A circuits. The names that appear on the functional schematics also appear on the block diagrams in Chapter 4. Thus, the descriptions in Chapter 4 can be correlated with both the block diagrams and the schematics.

Safety Considerations

This product is a Safety Class 1 instrument, which means that it is provided with a protective earth terminal. Refer to the Safety Summary page at the beginning of this manual for a summary of general safety information. Safety information for specific procedures is located at appropriate places in the manual.

7

Image 7

Agilent Technologies AGILENT MODELS 6023A and 6028A Scope, Calibration and Verification, Troubleshooting, Circuit Diagrams

Contents

Autoranging Certification Safety Summary Printing History Safety Symbol Definitions Table of Contents Replaceable Parts Scope TroubleshootingCircuit Diagrams Safety Considerations Item Description Manual Revisions Operation Verification Tests Calibration ProcedureIntroduction Test Equipment Required Test Equipment Required Type Required Characteristics USE Recommended Model 1KVA Initial Setup MON Calibration Procedure Iout Vout Measurement Techniques Performance TestsCR7 Constant Voltage CV Tests Current-Monitoring Resistor Setup Basic Test Setup RMS Measurement Test Setup, CV Pard Test Peak-To-Peak Measurement Test Setup, CV Pard Test KHz Noise, CV Peak-to-Peak Pard 6023A 6028A Load Transient Recovery Waveform Constant Current CC Tests CC Pard Test Setup Initial Troubleshooting Procedures Troubleshooting WAVEFORM/CONDITIONS Source Control Board Test Connector, A2J7PIN no Signal Name Vdc Electrostatic Protection Repair and Replacement A2 Control Board Removal A1 Main Board Removal A4 Power Mesh Board RemovalOverall Troubleshooting Procedure A3 Front-Panel Board Removal Measurement Using the TablesSetup Node Main Troubleshooting Setup Main Troubleshooting Setup Modified Mains Cord Set For Troubleshooting Front-Panel Troubleshooting Troubleshooting No-Output Failures A2J7-26 A2J7-25 PWM-ON PWM-OFF Defective Check Functional CircuitsBoard Node + Measurement Source Troubleshooting Bias SuppliesSymptoms Defective Circuit Check Components Symptoms Defective Check Functional Circuits Board Measurement Source Node +Node + N0DE Setup Measurement Power Section BlocksTroubleshooting AC-Turn-on Circuits Setup Measurement Source Relay Enable Troubleshooting PWM & ClockPower Limit PWM-OFF Troubleshooting DC-To-DC Converter+ OUT PWM-ON Troubleshooting CC Circuit Troubleshooting CV Circuit Troubleshooting OVP Circuit Troubleshooting Down ProgrammerA4U4OUT Waveforms SET Voltage Vdc Node + Page Block Diagram Overview Autoranging Power Block Diagram Simplified Schematic Simplified Schematic Down Programmer DC-to-DC Converter Constant-Voltage CV Circuit Pfet Control Signals Timing Diagram Control-Voltage Comparator Power-Limit ComparatorConstant-Current CC Circuit Overvoltage Protection OVP Circuit AC-Surge Dropout Detector Initial-Ramp CircuitPulse-Width Modulator PWM Bias Voltage Detector Display Circuits Second-Delay CircuitPage Reference Designators Replaceable Parts Description Abbreviations Ordering Information CR3 Electrical PartsCR1 CR2 XA2P2 XA2P1Mechanical Parts Control Board Assembly CR3 Page Page Page VR4 VR3VR5 DS1 CR5DS5 VR1 IC A/D Cmos 3-1/2 DGTVR2 Pfet NPN SI Chassis Electrical TS1 A4 Board Mechanical Parts A1TB1A2 Board Mechanical Parts A3 Board Mechanical Parts Option 240 240V Operation Option 220 220V Operation Component Location and Circuit Diagrams Schematic Diagram Notes Pin locations for other semi-conductors are shown below Top View, Top Covers Removed Main Board A1 Component Location Control Board A2 Component Location Front-Panel Board A3 Component Location Power Mesh Board A4 Component Location Page Page General Information SpecificationsOption 002 Hardware Status Indicators Table A-1. Specifications, Option Remote ProgrammingInput Compliance Voltage ± Current Programming Enable Output Impedance 10.2 k ohm ± 5% Temperature Coefficient On State logic low Remote Trip and Remote Reset TimingPower-on Preset Maximum Output Voltage logic high + Pard Typical Table A-1. Specifications, Option Pulse TimingBias Supplies DC Output Ratings 25C ± Short Circuit Output Current Connector Assembly Procedure Installation Operation Figure A-1. Mating Connector Assembly Local/Remote Programming Resistance Voltage or Current Figure A-4. Calculating Value of Series Dropping Resistor Remote Resistance Programming Figure A-5. Remote Resistance Programming Remote Monitoring Remote Control Status Indicators Overvoltage Remote Reset Figure A-8. Remote Control Power-On Preset Multiple Supply System Shutdown AC Dropout Buffer Circuit Bias Supplies Maintenance Troubleshooting Current Programming Troubleshooting Resistance and Voltage Programming Figure A-11. Troubleshooting Current Programming of CV Mode Figure A-13. Troubleshooting Status Indicators Page REF. Desig Model no Description Table A-3. Replacement Parts 100 101 VR9 Definitions Indicator and Qualifier SymbolsOLD Symbol NEW Symbol Logic Symbols and Definitions 102 Schematic Diagram Notes 103 Schematic Notes Figure A-15. Option 002 Board, Component Location 104 Schematic Notes Figure A-16. Option 002 Board, Schematic Diagram 105 Page Model 6028A Model 6023A107 108 From