Making chime paging automatically

Paging

The system allows you to page (transmit an announcement) the selected zone(s) and/or station(s) simultaneously.

*For paging a remote site, you can page the zone registered as the target in the site.

NOTE:

If you use zones, register zones in the System setting on a PC in advance.

1 Search for and select the zone or remote site you want to page (so that it is highlighted) in one of the search methods. (→P. 28-34)

*You can select up to 5 zones and/or stations in your site for paging. (→P. 30)

*For paging a zone in a remote site, you cannot select a zone. If you page (the pilot zone in) a remote site by searching for it from [REMOTE SITE] of SEARCH LIST, select the target site, and then select [PAGING] (so that it is highlighted). (→P. 32)

2 To set the priority (when “[] PRIORITY” is

displayed), press ZOOM/WIDE , and then press

to select the target priority (so that it is highlighted).

*If you will not set the priority, skip this step and press TALK or lift the handset. You can start paging after a tone.

3 Press TALK or ZOOM/WIDE , or lift the handset (when “[] [] PAGE” is displayed).

Handset

After a tone rings, start paging.

A receiver can answer it and communicate with you

by pressing

TALK

or lifting the handset, or pressing

the external call button*1.

*When the priority is set to "BROADCAST", no receiver can answer the paging.

The paging will be heard in priority to any other performances (of lower priority) including ongoing communications between stations. (→P. 23)

6 When you have ﬁnished paging, press OFF or hang up the handset.

*1: Connected to a room sub station and the necessary setting should be made in the System setting on a PC. (Be careful not to press the call button on a room sub station by mistake.)

Chime paging

The system allows you to make chime paging (transmit a chime) to all the stations in the designated zone(s) simultaneously.

*It may take long until the chime is triggered.

*For chime paging to a remote site, you can make chime paging to the pilot zone registered in the site, and cannot select a sound source.

NOTE:

If you use zones, register zones in the System setting on a PC in advance.

1 Search for and select the zone or remote site you want to make chime paging (so that it is highlighted) in one of the search methods. (→P. 32-34)

You can select up to 5 zones in your site for chime

paging. (→P. 30)

GETTING

target remote site from the list of [PLACED CALLS] (so

If you have selected the target zone or remote site by

using a speed dial button (so that it is highlighted), or the

that it is highlighted), skip to step 4.

STARTED

For chime paging to a zone in a remote site, you cannot

select a zone. If you make chime paging to (the pilot

zone in) a remote site by searching for it from [REMOTE

SITE] of SEARCH LIST, select the target site, and then

select [CHIME] (so that it is highlighted) (→P. 32) and

then skip to step 4.

SETTING

2 Press

TALK

ZOOM/WIDE

(when “[

] [ ] PLAY

AND

SOUND” is displayed).

ADJUSTMENT

3 Press

to select the sound source of chime from

the list (so that it is highlighted).

4 To set the priority (when “[ ] CHIME [

]

USING

PRIORITY” is displayed), press

ZOOM/WIDE

, and

then press

to select the target priority (so that it

THE

SYSTEM

is highlighted).

If you will not set the priority, skip this step and press

TALK

or lift the handset. Chime paging begins.

(Chime

paging begins after a ring of tone when the target

zone is other than the zone you belongs.)

5 Press		or		, or lift the handset	APPENDIX
	TALK		ZOOM/WIDE

(when “[ ] [		] CHIME” is displayed).

Chime paging begins.

(Chime paging begins after a ring of tone when the target zone is other than the zone you belongs.)

Handset