Appendices, A1 Electrical Characteristics | APC 40 130KVA specification

Appendices

A1 Electrical Characteristics

Selection of Protection Devices

UPS with common normal and bypass AC inputs

				Q3BP
			Bypass
		Q4S	Static Switch
	Upstream		PFC		Downstream
	circuit breaker		PFC		circuit breaker
	(not supplied) Main		Boost		(not supplied)
	(not supplied) Main	Q1	Rectifier Inverter	Q5N Output	(not supplied)
	Input	Q1	Rectifier Inverter	Q5N Output	Load

Normal AC
Bypass AC	Battery CB
	Battery CB

UPS unit with separate normal and bypass AC inputs
				Q3BP
Upstream
circuit breaker	Bypass		Bypass
(not supplied)	Bypass	Q4S	Static Switch
(not supplied)	Input	Q4S	Static Switch
	Input
Upstream						Downstream
Upstream			PFC			circuit breaker
circuit breaker			PFC			circuit breaker
circuit breaker	Main		Boost			(not supplied)
(not supplied)	Main	Q1	Boost	Q5N		(not supplied)
(not supplied)	Input	Q1	Rectifier Inverter	Q5N	Output	Load
	Input				Output

Battery CB

NOTE: Interrupted Transfer to Bypass Source:

If the bypass source is beyond the conditions stated below, the UPS will make an interrupted transfer (not more than 100 msec. in duration).

1.Bypass voltage greater than +15%, -15% from the UPS rated output voltage.

2.Bypass frequency greater than ±2 Hz from the UPS rated output frequency.

86-174010-00 B00

Appendices

A — 1

Image 57

APC 40 130KVA user manual Appendices, A1 Electrical Characteristics, Selection of Protection Devices

Contents

MGE Galaxy Page Schneider Electric MGE Galaxy MGE Galaxy Important Safety Instructions Environment This page left blank intentionally Contents Warranty and Product Registration MaintenanceService Solutions Team Three Phase Products Appendices Tables Figures UPS Serial Number Safety Rules Safety of personsSpecial precautions MGE Galaxy Symbol Usage Document IconsDisplay Icons Maintenance Setup and InstallationSection Descriptions Introduction Viii Introduction ScopeGeneral Description UPS power rating KVA Dimensions H x W x D MGE Galaxy 5000 UPS System with Battery Single Line Diagram Inside MGE Galaxy 5000 UPS Cabinet Inside the UPS Cabinet, Access to Connections UPS Cabinet Bottom View Layout Power Connection Terminals User-Machine Interface Display User-Machine Interface Display Display Screens Display Screens Relay Communication Card Relay Communication Card This page left blank intentionally Introduction Location Setup and Installation Layout of Cabinets Electrical Specifications Single UPS With Common Normal and Bypass AC Inputs Connection of Power Cables in a Single UPS UPS Can // interconnections Exchange-current interconnections Interconnections with the external system bypass cabinet Parallel Configuration for Increased Capacity Four UPSs XMB08 XMB07 XMB06 11 Adding Communication Cards Adding Communication Cards 12 Connection of Relay Communication Card Connection of the Relay Communications Card Communications Card Connection Example Characteristics of the input contacts Routing the Control/Communications Cables Single UPSGeneral-shutdown cable Parallel UPS Can cablesExchange-current cables Shutting Down a Single UPS Operation Shutting Down a Parallel Configuration Restarting a Single UPSLoad is protected by the UPS Load is protected by the UPSs Restarting a Parallel Configuration Operation of Mimic-Panel LEDs Single UPS Start Sequence on Normal AC InputSingle UPS Start Sequence on Bypass AC Input Operating Modes Load on Battery Power Personalization Settings Operating Mode Access to the Personalization FunctionsUPS Personalization Frequency Display Messages List Standard Mode Programmable ModeOperation of the Relay Communication Card Dry Contacts Load on Automatic AUTOMATIC-BYPASS Battery Temperature Fault This page left blank intentionally Identification of Alarms MaintenanceBattery power Life Cycle Monitoring LCM UPS Isolation UPS Isolation Single UPSLoad is no longer protected by the UPS Parallel UPS Configuration Without External Bypass Cabinet Shutdown and isolation of all the UPSs Parallel UPS Configuration With External Bypass Cabinet Return to the Normal Operation Return to Normal Single UPSUPS starts automatically LED 31 is on Parallel UPS Configuration Without External Bypass Cabinet UPS restarts and LED 31 is on Restart the UPS for which all switches are set to OFF Return to Normal Parallel UPS With External Bypass Cabinet Servicing Batteries Training CenterHz Training Center This page left blank intentionally A1 Electrical Characteristics AppendicesSelection of Protection Devices Limitation Input/Output Characteristics Bypass AC input Load outputInverter A2 Maximum Allowable Power for Parallel UPS Units A3 UPS Cabinet Major Internal Components MGE -Galaxy A4 Available Options A5 Environment Page Warranty Extension Warranty+ MGE Galaxy Warranty and Product RegistrationUser Information Product Information Technical Support and Product Services Scheduling Field Service Engineer SupportReturn Policy for Repair of Three Phase Products RGA MGE Galaxy AWG Glossary Igbt VAC MGE Galaxy Use this form Reorder Form Scenic Avenue Costa Mesa, CAPage Page Contact Information