IntraCore 35516 Series, Technical Support

IntraCore 35516 Series

Layer 2/3/4 Gigabit Switches

User’s Manual

Asanté Technologies, Inc.

821 Fox Lane

San Jose, CA 95131

USA

SALES

800-662-9686 Home/Office Solutions

800-303-9121 Enterprise Solutions

408-435-8388

TECHNICAL SUPPORT

801-566-8991: Worldwide www.asante.com/support

Copyright © 2003 Asanté Technologies, Inc. All rights reserved. No part of this document, or any associated artwork, product design, or design concept may be copied or reproduced in whole or in part by any means without the express written consent of Asanté Technologies, Inc. Asanté and IntraCore are registered trademarks and the Asanté logo, AsantéCare, Auto-Uplink, and IntraCare are trademarks of Asanté Technologies, Inc. All other brand names or product names are trademarks or registered trademarks of their respective holders. All features and specifications are subject to change without prior notice.

Rev. A 02/12/03

Page 2

Image 2

Asante Technologies user manual IntraCore 35516 Series, Technical Support

Contents

IntraCore 35516 Series IntraCore 35516 Series Technical Support Table of Contents Page Features Introduction Package Contents LEDs Front and Back Panel Descriptions Gbic Management and Configuration Console Interface Safety Overview Hardware Installation and SetupInstallation Overview Recommended Installation Tools Environmental Requirements Installation into an Equipment RackPower Requirements Cooling and Airflow Installing a Gbic Gigabit Interface Converters Gbic Care and Handling Installing the Optional Emergency Power SupplyRemoving a Gbic System Information System up since 103443 Fri Feb 07 1 10/100/1000BaseT Ports Cabling Procedures Connecting PowerConnecting to the Network Connecting to a Console SetupGigabit Ethernet Ports Cabling Procedures User Access Verification Password Specifies an Unencrypted line password will follow Setting PasswordsUnencrypted cleartext line password Specifies a Hidden line password will follow Routerconfig-if-veth1# Configuring an IP AddressSetting a Default IP Gateway Address Routerconfig# boot system flash bank1bank2 Restoring Factory DefaultsSystem Boot Parameters Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Command Show ? Purpose Command Purpose Privileged Top Privileged Exec ModeRouter enable Password Router# Command Exit end Ctrl-Z Purpose Global Configuration ModeCommand Purpose Router# configure terminal Interface Configuration Mode Router Configuration Mode Route-Map Configuration Mode Advanced Features Supported within the Command Mode Command Help Purpose Routerconfig# routed rip Invalid input detected at marker Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# route Ambiguous command. Routerconfig# Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Routerconfig# router Command incomplete. Routerconfig# Router# confTab Router# configure Moving Around on the Command LineCompleting a Partial Command Name Keystrokes Purpose Deleting Entries Editing Command Lines that WrapRouter# co? configure copy Router# co Keystrokes Purpose Press the Delete or Backspace Transposing Mistyped Characters Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling Capitalization Password Passwords and Privileges CommandsEnable Password Routerconfig-line# password Asante Service Password-Encryption Changing the Password Managing the System and Configuration FilesSetting the System Clock Managing the System Trace Packet Routes Enable the System LogDisplaying the Operating Configuration Test Connections with Ping Tests Configuration to Nvram Managing Configuration FilesConfiguring from the Terminal Routerconfig# hostname newname Newnameconfig# end Copying Configuration Files to a Network Server Running-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Startup-config Routerconfig# duplicate-ip detect Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Disable the Snmp Protocol Maximum Age Forward TimeHello Time Priority Port Priority Routerconfig# mac-address-table aging-timeMAC Address Table Port Path Cost Assign IP Addresses to Network Interfaces Configuring IPConfiguring IP Addressing Class Address or Range Status Cidr Prefix Class C Equivalent Host Addresses Command PurposeAssign Multiple IP Addresses to Network Interfaces Define a Static ARP Cache Establish Address ResolutionConfiguring IP Routing Secondary Configuring Static Routes Route Source Default Distance Allow Unicast Updates for RIP Configuring RIPEnable RIP Neighbor ip-address Redistribute Routing Information Command Purpose Route-map map-tagdeny permit sequenceSpecify a RIP Version Set Administrative Distance Set Metrics for Redistributed Routes Filtering Routing Information Generate a Default RouteSuppress Routing Updates through an Interface Manage Authentication Keys Adjust TimersEnable or Disable Split-horizon Command Purpose Offset-list access-list-name in out Configuring IP Multicast Routing Monitor and Maintain RIP Purpose Ip igmp query-interval 1-65535 seconds Configuring IgmpModifying the Igmp Host-Query Message Interval Changing the Igmp Version CommandConfiguring the Router as a Statically Connected Member Seconds Configuring Dvmrp Nbr-timeout 35-8000 seconds Default value 200 seconds Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Report-interval Using Access Lists Create a Standard Access List Create an Expanded Access List Destination address to match. e.g Operator equal to Creating an Access List with a NameApplying an Access List to an Interface Operator greater then Configure ABR Type Configuring OspfEnable Ospf Command Purpose Router ospf Step Configure Ospf Network Type Configure CompatibilityConfigure Ospf Interface Parameters Configure Ospf Not So Stubby Area Nssa Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Command Purpose Neighbor ip-address priority number Create Virtual Links Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Not-advertised Refresh Timer Configuration Control Default MetricsConfigure Route Calculation Timers Redistribute Routes into Ospf Command Purpose Distance ospf external distance1 inter-area Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Suppress Routes on an Interface Router ip-address Name Vrrp Configuration Virtual Router Redundancy Protocol Vrrp Monitoring and Maintaining the Network Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Change Irdp Parameters Show ip prefix-list prefix-list-name Command Purpose Show arp interfaceShow access-lists access-list Show ip irdp Vlan Configuration Creating or Modifying a Vlan Deleting a Vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Routerconfig# no vlan Routerconfig# exit Router# show vlan Trunk Ieee 802.1Q Static AccessVlan Port Membership Modes Trunk allowed vlan add all except Command Purpose Routerconfig# vlan dot1q tag native3 Dot1q Tunnel Mode dot1q-tunnel Appendix A. Basic Troubleshooting Problem Possible Solutions Technical Support and Warranty Appendix B. SpecificationsPhysical Characteristics Standards Compliance IntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Pin Number Signal Name Appendix D. Console Port Pin Outs Appendix E. Online Warranty Registration