Manuals / Asante Technologies / Computer Equipment / Switch

Asante Technologies 35516 Command Purpose Show arp interface, Show access-lists access-list

Models: 35516

1 77

Page 66

Use any of the following commands in top mode.

Command	Purpose
show arp [interface]	Display the entries in the ARP table.

show access-lists [access-list-	Display the contents of one or all current access
name]	lists.
show ip prefix-list [prefix-list-name]	Display the contents of current IP prefix lists.

show ip protocols	Display active IP routing protocol statistics.

show ip irdp	Display IRDP values.

show ip route [bgp rip ospf	Display the current state of the routing table.
connected kernel static address
prefix]
ping {host address}	Test network node reach-ability.

traceroute {host destination}	Trace packet routes through the network.

Page 66

Image 66

Asante Technologies 35516 user manual Command Purpose Show arp interface, Show access-lists access-list, Show ip irdp

Contents

IntraCore 35516 Series IntraCore 35516 Series Technical SupportTable of Contents Page Features IntroductionPackage Contents LEDsFront and Back Panel Descriptions GbicManagement and Configuration Console InterfaceSafety Overview Hardware Installation and SetupInstallation Overview Recommended Installation ToolsEnvironmental Requirements Installation into an Equipment RackPower Requirements Cooling and AirflowInstalling a Gbic Gigabit Interface ConvertersGbic Care and Handling Installing the Optional Emergency Power SupplyRemoving a Gbic System Information System up since 103443 Fri Feb 07Connecting Power Connecting to the Network1 10/100/1000BaseT Ports Cabling Procedures Setup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console User Access Verification Password Specifies an Unencrypted line password will follow Setting PasswordsUnencrypted cleartext line password Specifies a Hidden line password will followConfiguring an IP Address Setting a Default IP Gateway AddressRouterconfig-if-veth1# Restoring Factory Defaults System Boot ParametersRouterconfig# boot system flash bank1bank2 Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Command Show ? PurposePrivileged Top Privileged Exec Mode Router enable Password Router#Command Purpose Global Configuration Mode Command Purpose Router# configure terminalCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Router Configuration Mode Route-Map Configuration ModeAdvanced Features Supported within the Command Mode Command Help PurposeRouterconfig# routed rip Invalid input detected at marker Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# route Ambiguous command. Routerconfig#Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Routerconfig# router Command incomplete. Routerconfig#Router# confTab Router# configure Moving Around on the Command LineCompleting a Partial Command Name Keystrokes PurposeDeleting Entries Editing Command Lines that WrapRouter# co? configure copy Router# co Keystrokes Purpose Press the Delete or BackspaceTransposing Mistyped Characters Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling CapitalizationPassword Passwords and Privileges CommandsEnable Password Routerconfig-line# password AsanteService Password-Encryption Changing the Password Managing the System and Configuration FilesSetting the System Clock Managing the SystemTrace Packet Routes Enable the System LogDisplaying the Operating Configuration Test Connections with Ping TestsConfiguration to Nvram Managing Configuration FilesConfiguring from the Terminal Routerconfig# hostname newname Newnameconfig# endCopying Configuration Files to a Network Server Running-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Startup-configRouterconfig# duplicate-ip detect Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Disable the Snmp ProtocolMaximum Age Forward TimeHello Time PriorityPort Priority Routerconfig# mac-address-table aging-timeMAC Address Table Port Path CostAssign IP Addresses to Network Interfaces Configuring IPConfiguring IP Addressing Class Address or Range StatusCommand Purpose Assign Multiple IP Addresses to Network InterfacesCidr Prefix Class C Equivalent Host Addresses Define a Static ARP Cache Establish Address ResolutionConfiguring IP Routing SecondaryConfiguring Static Routes Route Source Default DistanceAllow Unicast Updates for RIP Configuring RIPEnable RIP Neighbor ip-addressCommand Purpose Route-map map-tagdeny permit sequence Specify a RIP VersionRedistribute Routing Information Set Administrative Distance Set Metrics for Redistributed RoutesGenerate a Default Route Suppress Routing Updates through an InterfaceFiltering Routing Information Manage Authentication Keys Adjust TimersEnable or Disable Split-horizon Command Purpose Offset-list access-list-name in outConfiguring IP Multicast Routing Monitor and Maintain RIPConfiguring Igmp Modifying the Igmp Host-Query Message IntervalPurpose Ip igmp query-interval 1-65535 seconds Changing the Igmp Version CommandConfiguring the Router as a Statically Connected Member SecondsConfiguring Dvmrp Nbr-timeout 35-8000 secondsDefault value 200 seconds Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Report-intervalUsing Access Lists Create a Standard Access ListCreate an Expanded Access List Destination address to match. e.gOperator equal to Creating an Access List with a NameApplying an Access List to an Interface Operator greater thenConfigure ABR Type Configuring OspfEnable Ospf Command Purpose Router ospf StepConfigure Compatibility Configure Ospf Interface ParametersConfigure Ospf Network Type Configure Ospf Not So Stubby Area Nssa Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Command Purpose Neighbor ip-address priority numberCreate Virtual Links Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Not-advertisedRefresh Timer Configuration Control Default MetricsConfigure Route Calculation Timers Redistribute Routes into OspfCommand Purpose Distance ospf external distance1 inter-area Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Suppress Routes on an InterfaceRouter ip-address NameVrrp Configuration Virtual Router Redundancy Protocol VrrpMonitoring and Maintaining the Network Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Change Irdp ParametersShow ip prefix-list prefix-list-name Command Purpose Show arp interfaceShow access-lists access-list Show ip irdpVlan Configuration Creating or Modifying a VlanRouterconfig# interface veth2 vlan Routerconfig-if-veth2# Routerconfig# no vlan Routerconfig# exit Router# show vlanDeleting a Vlan Static Access Vlan Port Membership ModesTrunk Ieee 802.1Q Command Purpose Routerconfig# vlan dot1q tag native 3 Dot1q TunnelTrunk allowed vlan add all except Mode dot1q-tunnel Appendix A. Basic Troubleshooting Problem Possible SolutionsTechnical Support and Warranty Appendix B. SpecificationsPhysical Characteristics Standards ComplianceAppendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration

Command

Purpose

show arp [interface]

show access-lists [access-list-

show ip prefix-list [prefix-list-name]

show ip irdp

show ip route [bgp rip ospf

connected kernel static address