Restoring Factory Defaults | Asante Technologies 35516 specs

2.10 Restoring Factory Defaults

If you ever need to restore the switch to its factory default settings, follow the commands shown in the following screen.

Router> enable Router# reload ?

factory-default Reset ALL system parameters to factory default <cr>

Router# reload factory-default

The switch is now ready for configuration. Refer to the following chapters for management and configuration information.

2.11 System Boot Parameters

The IC35516 has two boot banks to store its runtime code. You can select which bank will be used for the next boot with the following command:

Router(config)# boot system flash {bank1bank2}

Page 18

Image 18

Asante Technologies 35516 Restoring Factory Defaults, System Boot Parameters, Routerconfig# boot system flash bank1bank2

Contents

IntraCore 35516 Series IntraCore 35516 Series Technical Support Table of Contents Page Features Introduction Package Contents LEDs Front and Back Panel Descriptions Gbic Management and Configuration Console Interface Safety Overview Hardware Installation and SetupInstallation Overview Recommended Installation Tools Environmental Requirements Installation into an Equipment RackPower Requirements Cooling and Airflow Installing a Gbic Gigabit Interface Converters Gbic Care and Handling Installing the Optional Emergency Power SupplyRemoving a Gbic System Information System up since 103443 Fri Feb 07 Connecting Power Connecting to the Network1 10/100/1000BaseT Ports Cabling Procedures Setup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console User Access Verification Password Specifies an Unencrypted line password will follow Setting PasswordsUnencrypted cleartext line password Specifies a Hidden line password will follow Configuring an IP Address Setting a Default IP Gateway AddressRouterconfig-if-veth1# Restoring Factory Defaults System Boot ParametersRouterconfig# boot system flash bank1bank2 Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Command Show ? Purpose Privileged Top Privileged Exec Mode Router enable Password Router#Command Purpose Global Configuration Mode Command Purpose Router# configure terminalCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Router Configuration Mode Route-Map Configuration Mode Advanced Features Supported within the Command Mode Command Help Purpose Routerconfig# routed rip Invalid input detected at marker Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# route Ambiguous command. Routerconfig# Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Routerconfig# router Command incomplete. Routerconfig# Router# confTab Router# configure Moving Around on the Command LineCompleting a Partial Command Name Keystrokes Purpose Deleting Entries Editing Command Lines that WrapRouter# co? configure copy Router# co Keystrokes Purpose Press the Delete or Backspace Transposing Mistyped Characters Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling Capitalization Password Passwords and Privileges CommandsEnable Password Routerconfig-line# password Asante Service Password-Encryption Changing the Password Managing the System and Configuration FilesSetting the System Clock Managing the System Trace Packet Routes Enable the System LogDisplaying the Operating Configuration Test Connections with Ping Tests Configuration to Nvram Managing Configuration FilesConfiguring from the Terminal Routerconfig# hostname newname Newnameconfig# end Copying Configuration Files to a Network Server Running-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Startup-config Routerconfig# duplicate-ip detect Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Disable the Snmp Protocol Maximum Age Forward TimeHello Time Priority Port Priority Routerconfig# mac-address-table aging-timeMAC Address Table Port Path Cost Assign IP Addresses to Network Interfaces Configuring IPConfiguring IP Addressing Class Address or Range Status Command Purpose Assign Multiple IP Addresses to Network InterfacesCidr Prefix Class C Equivalent Host Addresses Define a Static ARP Cache Establish Address ResolutionConfiguring IP Routing Secondary Configuring Static Routes Route Source Default Distance Allow Unicast Updates for RIP Configuring RIPEnable RIP Neighbor ip-address Command Purpose Route-map map-tagdeny permit sequence Specify a RIP VersionRedistribute Routing Information Set Administrative Distance Set Metrics for Redistributed Routes Generate a Default Route Suppress Routing Updates through an InterfaceFiltering Routing Information Manage Authentication Keys Adjust TimersEnable or Disable Split-horizon Command Purpose Offset-list access-list-name in out Configuring IP Multicast Routing Monitor and Maintain RIP Configuring Igmp Modifying the Igmp Host-Query Message IntervalPurpose Ip igmp query-interval 1-65535 seconds Changing the Igmp Version CommandConfiguring the Router as a Statically Connected Member Seconds Configuring Dvmrp Nbr-timeout 35-8000 seconds Default value 200 seconds Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Report-interval Using Access Lists Create a Standard Access List Create an Expanded Access List Destination address to match. e.g Operator equal to Creating an Access List with a NameApplying an Access List to an Interface Operator greater then Configure ABR Type Configuring OspfEnable Ospf Command Purpose Router ospf Step Configure Compatibility Configure Ospf Interface ParametersConfigure Ospf Network Type Configure Ospf Not So Stubby Area Nssa Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Command Purpose Neighbor ip-address priority number Create Virtual Links Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Not-advertised Refresh Timer Configuration Control Default MetricsConfigure Route Calculation Timers Redistribute Routes into Ospf Command Purpose Distance ospf external distance1 inter-area Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Suppress Routes on an Interface Router ip-address Name Vrrp Configuration Virtual Router Redundancy Protocol Vrrp Monitoring and Maintaining the Network Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Change Irdp Parameters Show ip prefix-list prefix-list-name Command Purpose Show arp interfaceShow access-lists access-list Show ip irdp Vlan Configuration Creating or Modifying a Vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2# Routerconfig# no vlan Routerconfig# exit Router# show vlanDeleting a Vlan Static Access Vlan Port Membership ModesTrunk Ieee 802.1Q Command Purpose Routerconfig# vlan dot1q tag native 3 Dot1q TunnelTrunk allowed vlan add all except Mode dot1q-tunnel Appendix A. Basic Troubleshooting Problem Possible Solutions Technical Support and Warranty Appendix B. SpecificationsPhysical Characteristics Standards Compliance Appendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Pin Number Signal Name Appendix D. Console Port Pin Outs Appendix E. Online Warranty Registration

Asante Technologies 35516 user manual Restoring Factory Defaults, System Boot Parameters

Models: 35516

2.10 Restoring Factory Defaults

2.11 System Boot Parameters

Router(config)# boot system flash {bank1bank2}