Mode dot1q-tunnel

Use the following commands to configure an interface as an IEEE 802.1q tunnel port:

Command	Purpose
Router(config)# interface IFNAME	Enter the interface name to access the interface
	configuration node.

Router(config-if-IFNAME)# switchport	This command will put the interface into IEEE
mode dot1q-tunnel	802.1q dot1q-tunnel access mode.
	Use the no form of this command to reset to the
	default of static-access mode.
Router(config-if-IFNAME)# switchport	This command will assign a VLAN ID specific to
access vlan vid	the particular customer.
	Use the no form of this command to reset the
	access VLAN to default VID 1.

Router(config-if-IFNAME)# end	Return to Enable node.

Page 71

Image 71

Asante Technologies 35516 user manual Mode dot1q-tunnel

Contents

IntraCore 35516 Series Technical Support IntraCore 35516 Series Table of Contents Page Introduction Features LEDs Package Contents Gbic Front and Back Panel Descriptions Console Interface Management and Configuration Recommended Installation Tools Hardware Installation and SetupInstallation Overview Safety Overview Cooling and Airflow Installation into an Equipment RackPower Requirements Environmental Requirements Gigabit Interface Converters Installing a Gbic System Information System up since 103443 Fri Feb 07 Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and Handling 1 10/100/1000BaseT Ports Cabling Procedures Connecting PowerConnecting to the Network Connecting to a Console SetupGigabit Ethernet Ports Cabling Procedures User Access Verification Password Specifies a Hidden line password will follow Setting PasswordsUnencrypted cleartext line password Specifies an Unencrypted line password will follow Routerconfig-if-veth1# Configuring an IP AddressSetting a Default IP Gateway Address Routerconfig# boot system flash bank1bank2 Restoring Factory DefaultsSystem Boot Parameters Command Show ? Purpose Understanding the Command Line Interface CLIUser Top User Exec Mode Access Each Command Mode Command Purpose Privileged Top Privileged Exec ModeRouter enable Password Router# Command Exit end Ctrl-Z Purpose Global Configuration ModeCommand Purpose Router# configure terminal Interface Configuration Mode Route-Map Configuration Mode Router Configuration Mode Command Help Purpose Advanced Features Supported within the Command Mode Routerconfig# route Ambiguous command. Routerconfig# Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# routed rip Invalid input detected at marker Routerconfig# router Command incomplete. Routerconfig# Using CLI Command HistoryUsing the No and Default Forms of Commands Using Command-Line Editing Features and Shortcuts Keystrokes Purpose Moving Around on the Command LineCompleting a Partial Command Name Router# confTab Router# configure Keystrokes Purpose Press the Delete or Backspace Editing Command Lines that WrapRouter# co? configure copy Router# co Deleting Entries Controlling Capitalization Redisplaying the Current Command LineScrolling Down a Line or a Screen Transposing Mistyped Characters Routerconfig-line# password Asante Passwords and Privileges CommandsEnable Password Password Service Password-Encryption Managing the System Managing the System and Configuration FilesSetting the System Clock Changing the Password Test Connections with Ping Tests Enable the System LogDisplaying the Operating Configuration Trace Packet Routes Routerconfig# hostname newname Newnameconfig# end Managing Configuration FilesConfiguring from the Terminal Configuration to Nvram Copying Configuration Files to a Network Server Startup-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Running-config Disable the Snmp Protocol Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Routerconfig# duplicate-ip detect Priority Forward TimeHello Time Maximum Age Port Path Cost Routerconfig# mac-address-table aging-timeMAC Address Table Port Priority Class Address or Range Status Configuring IPConfiguring IP Addressing Assign IP Addresses to Network Interfaces Cidr Prefix Class C Equivalent Host Addresses Command PurposeAssign Multiple IP Addresses to Network Interfaces Secondary Establish Address ResolutionConfiguring IP Routing Define a Static ARP Cache Route Source Default Distance Configuring Static Routes Neighbor ip-address Configuring RIPEnable RIP Allow Unicast Updates for RIP Redistribute Routing Information Command Purpose Route-map map-tagdeny permit sequenceSpecify a RIP Version Set Metrics for Redistributed Routes Set Administrative Distance Filtering Routing Information Generate a Default RouteSuppress Routing Updates through an Interface Command Purpose Offset-list access-list-name in out Adjust TimersEnable or Disable Split-horizon Manage Authentication Keys Monitor and Maintain RIP Configuring IP Multicast Routing Purpose Ip igmp query-interval 1-65535 seconds Configuring IgmpModifying the Igmp Host-Query Message Interval Seconds CommandConfiguring the Router as a Statically Connected Member Changing the Igmp Version Nbr-timeout 35-8000 seconds Configuring Dvmrp Report-interval Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Default value 200 seconds Create a Standard Access List Using Access Lists Destination address to match. e.g Create an Expanded Access List Operator greater then Creating an Access List with a NameApplying an Access List to an Interface Operator equal to Command Purpose Router ospf Step Configuring OspfEnable Ospf Configure ABR Type Configure Ospf Network Type Configure CompatibilityConfigure Ospf Interface Parameters Command Purpose Neighbor ip-address priority number Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Configure Ospf Not So Stubby Area Nssa Not-advertised Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Create Virtual Links Redistribute Routes into Ospf Control Default MetricsConfigure Route Calculation Timers Refresh Timer Configuration Suppress Routes on an Interface Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Command Purpose Distance ospf external distance1 inter-area Name Router ip-address Virtual Router Redundancy Protocol Vrrp Vrrp Configuration Change Irdp Parameters Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Monitoring and Maintaining the Network Show ip irdp Command Purpose Show arp interfaceShow access-lists access-list Show ip prefix-list prefix-list-name Creating or Modifying a Vlan Vlan Configuration Deleting a Vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Routerconfig# no vlan Routerconfig# exit Router# show vlan Trunk Ieee 802.1Q Static AccessVlan Port Membership Modes Trunk allowed vlan add all except Command Purpose Routerconfig# vlan dot1q tag native3 Dot1q Tunnel Mode dot1q-tunnel Problem Possible Solutions Appendix A. Basic Troubleshooting Standards Compliance Appendix B. SpecificationsPhysical Characteristics Technical Support and Warranty IntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Appendix D. Console Port Pin Outs Pin Number Signal Name Appendix E. Online Warranty Registration

Router(config-if-IFNAME)# end