User Access Verification Password | Asante Technologies 35516

•Under the Settings tab, choose VT100 for Emulation mode

•Select Terminal keys for Function, Arrow, and Ctrl keys. Be sure the setting is for Terminal keys, NOT Windows keys

•Back under the Connect To tab, press the Configuration button

•Set the data rate to 9600 Baud

•Set data format to 8 data bits, 1 stop bit and no parity

•Set flow control to NONE

Now that terminal is set up correctly, power on the switch (boot sequence will display in terminal.)

After connecting to the console, a prompt like the following will appear:

User Access Verification

Password:

By default, the initial password for access via console and telnet is Asante (case-sensitive). See the following section for setting new passwords on the terminal lines.

Page 15

Image 15

Asante Technologies 35516 user manual User Access Verification Password

Contents

IntraCore 35516 Series Technical Support IntraCore 35516 Series Table of Contents Page Introduction Features LEDs Package Contents Gbic Front and Back Panel Descriptions Console Interface Management and Configuration Recommended Installation Tools Hardware Installation and SetupInstallation Overview Safety Overview Cooling and Airflow Installation into an Equipment RackPower Requirements Environmental Requirements Gigabit Interface Converters Installing a Gbic System Information System up since 103443 Fri Feb 07 Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and Handling Connecting Power Connecting to the Network1 10/100/1000BaseT Ports Cabling Procedures Setup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console User Access Verification Password Specifies a Hidden line password will follow Setting PasswordsUnencrypted cleartext line password Specifies an Unencrypted line password will follow Configuring an IP Address Setting a Default IP Gateway AddressRouterconfig-if-veth1# Restoring Factory Defaults System Boot ParametersRouterconfig# boot system flash bank1bank2 Command Show ? Purpose Understanding the Command Line Interface CLIUser Top User Exec Mode Access Each Command Mode Privileged Top Privileged Exec Mode Router enable Password Router#Command Purpose Global Configuration Mode Command Purpose Router# configure terminalCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Route-Map Configuration Mode Router Configuration Mode Command Help Purpose Advanced Features Supported within the Command Mode Routerconfig# route Ambiguous command. Routerconfig# Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# routed rip Invalid input detected at marker Routerconfig# router Command incomplete. Routerconfig# Using CLI Command HistoryUsing the No and Default Forms of Commands Using Command-Line Editing Features and Shortcuts Keystrokes Purpose Moving Around on the Command LineCompleting a Partial Command Name Router# confTab Router# configure Keystrokes Purpose Press the Delete or Backspace Editing Command Lines that WrapRouter# co? configure copy Router# co Deleting Entries Controlling Capitalization Redisplaying the Current Command LineScrolling Down a Line or a Screen Transposing Mistyped Characters Routerconfig-line# password Asante Passwords and Privileges CommandsEnable Password Password Service Password-Encryption Managing the System Managing the System and Configuration FilesSetting the System Clock Changing the Password Test Connections with Ping Tests Enable the System LogDisplaying the Operating Configuration Trace Packet Routes Routerconfig# hostname newname Newnameconfig# end Managing Configuration FilesConfiguring from the Terminal Configuration to Nvram Copying Configuration Files to a Network Server Startup-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Running-config Disable the Snmp Protocol Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Routerconfig# duplicate-ip detect Priority Forward TimeHello Time Maximum Age Port Path Cost Routerconfig# mac-address-table aging-timeMAC Address Table Port Priority Class Address or Range Status Configuring IPConfiguring IP Addressing Assign IP Addresses to Network Interfaces Command Purpose Assign Multiple IP Addresses to Network InterfacesCidr Prefix Class C Equivalent Host Addresses Secondary Establish Address ResolutionConfiguring IP Routing Define a Static ARP Cache Route Source Default Distance Configuring Static Routes Neighbor ip-address Configuring RIPEnable RIP Allow Unicast Updates for RIP Command Purpose Route-map map-tagdeny permit sequence Specify a RIP VersionRedistribute Routing Information Set Metrics for Redistributed Routes Set Administrative Distance Generate a Default Route Suppress Routing Updates through an InterfaceFiltering Routing Information Command Purpose Offset-list access-list-name in out Adjust TimersEnable or Disable Split-horizon Manage Authentication Keys Monitor and Maintain RIP Configuring IP Multicast Routing Configuring Igmp Modifying the Igmp Host-Query Message IntervalPurpose Ip igmp query-interval 1-65535 seconds Seconds CommandConfiguring the Router as a Statically Connected Member Changing the Igmp Version Nbr-timeout 35-8000 seconds Configuring Dvmrp Report-interval Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Default value 200 seconds Create a Standard Access List Using Access Lists Destination address to match. e.g Create an Expanded Access List Operator greater then Creating an Access List with a NameApplying an Access List to an Interface Operator equal to Command Purpose Router ospf Step Configuring OspfEnable Ospf Configure ABR Type Configure Compatibility Configure Ospf Interface ParametersConfigure Ospf Network Type Command Purpose Neighbor ip-address priority number Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Configure Ospf Not So Stubby Area Nssa Not-advertised Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Create Virtual Links Redistribute Routes into Ospf Control Default MetricsConfigure Route Calculation Timers Refresh Timer Configuration Suppress Routes on an Interface Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Command Purpose Distance ospf external distance1 inter-area Name Router ip-address Virtual Router Redundancy Protocol Vrrp Vrrp Configuration Change Irdp Parameters Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Monitoring and Maintaining the Network Show ip irdp Command Purpose Show arp interfaceShow access-lists access-list Show ip prefix-list prefix-list-name Creating or Modifying a Vlan Vlan Configuration Routerconfig# interface veth2 vlan Routerconfig-if-veth2# Routerconfig# no vlan Routerconfig# exit Router# show vlanDeleting a Vlan Static Access Vlan Port Membership ModesTrunk Ieee 802.1Q Command Purpose Routerconfig# vlan dot1q tag native 3 Dot1q TunnelTrunk allowed vlan add all except Mode dot1q-tunnel Problem Possible Solutions Appendix A. Basic Troubleshooting Standards Compliance Appendix B. SpecificationsPhysical Characteristics Technical Support and Warranty Appendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal Name Appendix E. Online Warranty Registration