Avaya IP Office Phone Technical Specifications, General, Interfaces, Interface Information

Technical Data

Technical Specifications - Page 79

Technical Specifications

General

Dimensions

IP401:

Width: 255mm (10").

Height: 71mm (2.8")

Depth: 235mm (9.3")

(unboxed)

IP403/6/12 & Exp. Modules :

Width: 445mm (17.5")

Height: 71mm (2.8")

Depth: 245mm (9.7")

Dimensions

IP401:

Width: 304mm (13.4")

Height: 105mm (4.2")

Depth: 305mm (12")

(boxed)

IP403/6/12 & Exp. Modules :

Width: 445mm (17.5")

Height: 71mm (2.8")

Depth: 245mm (9.7")

Environmental

0 to +40°C. 95% relative humidity, non-condensing.

Weight (unboxed)

401

403

406

412

Analog16

DT/DS16

DT/DS30

WAN3

So8

Phones8 …16

…30

Kgs

1.2

2.6

3.0

3.0

2.9

3.0

3.50

2.8

2.8

2.8

2.9

3.10

lbs

2.6

5.8

6.6

6.7

6.5

6.7

7.8

6.3

6.3

6.3

6.5

6.94

Weight (boxed)

401

403

406

412

Analog16

DT/DS16

DT/DS30

WAN3

So8

Phones8 …16

…30

Kgs

2.4

3.85

4.3

4.3

4.2

4.3

4.8

4.1

4.1

4.1

4.2

4.4

lbs

5.4

8.6

9.6

9.6

9.4

9.6

10.8

9.2

9.2

9.2

9.4

9.7

Power Supply

2.5mm DC inlet socket. 24Vdc Power input. Rating 24Vd.c., 2A max.

Consumption

401

403

406412

Analog16

DT/DS16

DT/DS30

WAN3

So8

Phones8 …16

…30

(nominal Watts)

24

26

16 17.5

5

24

30

12

24

12

16

30

Lump-in-Line PSU

Power Requirements: I/P 100-240Vac, 50/60Hz, 81-115VA, Input current 2A max

Standard PSUs: O/P 24Vdc, 1.875A, output power 45W max.

DS30 80W PSU: O/P 16Vdc, 5A, output power 80W max.

Lump-in-line PSUs are CE/UL/Dentori Safety Approved.

Interfaces

Interface

Information

DTE

25 way D-Type female connector, V.24/V.28. (9 way D-type on IP412s)

ISDN

ROW Interfaces:

BRI :

RJ45 sockets. ETSI S/T Interface to CTR3 for Pan European Connection.

PRI E1:

RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.

PRI E1-R2: RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.

PRI E1-R2:

75Ω BNC Coax.. ETSI T Interface.

PRI T1:

RJ45 socket: FCC Part 68/JATE connection.

USA Interfaces:

PRI T1 Service:

Ground Start (GS) – Default, E&M, 56k data for 5ESS, 56/64/64 restricted for 4ESS

PRI ISDN Switch support:

4ESS, 5ESS, DMS-100, DMS-250 (includes conformance to ANSI T1.607 & Bellcore

Special Report SR4287, 1992

PRI ISDN Services:

AT&T Megacom 800, AT&T WATS (4ESS), AT&T SDS Accunet 56kB/s & 64kB/s (4ESS),

AT&T Multiquest (4ESS).

Analog ports

RJ45 sockets: Loop start/Ground start (region dependant)

Power Fail ports

RJ45 sockets: telephone ports act as master sockets

ISDN

BRI: B-channel 64kbps or 56kbps, D-channel 16kbps.

Data Rates

PRI: B-channel 64kbps or 56kbps, D-channel 64kbps.

Telephone

RJ45 sockets. EU - Telephone ports act as master sockets.

CLI Schemes: DTMFA, DTMFC, DTMFD, FSK and UK20.

REN = 2

Off Hook current = 25mA.

Ring Voltage = 40V (nominal) RMS.

External Bell (via analog port); REN = 1

LAN

RJ45 sockets. Auto-negotiating 10/100BaseT Ethernet (10Mbps).

Port 8 is MDI/MDIX switchable via the adjacent Cascade pushbutton switch.

Refer to pages 11, 15 and 19.

WAN

37 way D-Type female sockets. X.21 interface to 2048k bps, V.35 interface to 2048k bps and

V.24 Interface to 19k2 bps.

Audio

3.5mm Stereo Jack socket. Input impedance - 10k /channel.

Maximum a.c. signal – 200mV rms.

External

3.5mm Stereo Jack socket. Switching Capacity - 0.7A.

Control

Maximum Voltage - 55V d.c. On state resistance - 0.7Ω.

Short circuit current - 1A. Reverse circuit current capacity - 1.4A.

IP Office Installation Manual	Technical Data - Page 79
40DHB0002USCL – Issue 9 (28th October 2003)	Technical Specifications