Ipsi address configuration | Avaya S8500 guide

Chapter 6: IP interface configuration

IPSI address configuration

The IPSI circuit pack receives an IP address:

●Statically with static IP addressing, if the control network is nondedicated (public) through the customer network.

●Dynamically with dynamic host configuration protocol (DHCP), if the control network is dedicated (private).

Note:

To program DHCP addressing, you must complete certain sequences within a predetermined time-out interval. Avaya recommends that you read the following procedure completely before you start so that you are familiar with these sequences in advance.

Perform one of the following tasks depending on whether you use static or dynamic addressing:

●Programming the IPSI for static addressing on page 54

●Programming the IPSI for DHCP addressing on page 59

Programming the IPSI for static addressing

! Important:

If an IPSI is in a port network that is backed up with the Enterprise Survivable Server (ESS) option you must use static addressing for the ESS to provide service to the port network.

54 Installing and Configuring the Avaya S8500 Media Server

February 2007

Image 54

Avaya S8500 manual Ipsi address configuration, Programming the Ipsi for static addressing

Contents

Installing and Configuring the Avaya S8500 Media Server Release Avaya Inc All Rights Reserved Introduction Media server configuration Install an S8500 Media Server as an LSP Index 101 Introduction Audience How to use Avaya installation documents Pre-installation requirements Preinstallation tasks to complete at the customer siteVerifying that all the required equipment is on site Ensuring that the preinstallation tasks are complete S8500 hardware S8500C front panel S8500B front panel Equipment specifications UPS S8500 Media Server specifications Feature S8500B S8500C CD-ROM/DVD-ROM IDE Acoustical About the Server Availability Management Processor About Samp functionalityAbout Samp connections Samp connections for S8500B About Samp software Samp connections for S8500C About media server port connections S8500 port connections S8500C Media Server connectivity guide About modem connections Modem connectivity on the S8500 Media Server About media gateways About Processor EthernetModem options About Processor Ethernet About S8500 LSP mode S8500 LSP license file About SSH TN8412AP Sipi Snmp Configuration Configuring the Snmp modules in the UPS Default IP addresses for the UPS Prerequisites for configuring the Snmp module Administering the Snmp module Security Alert Setting selected traps alarming Default IP addresses for the Ethernet switch Preparing to configure the Ethernet switch Configuring the Ethernet switch Page Page Communication Manager installation Clearing the ARP cache on the laptop Applying power to the media server Accessing the media serverConfiguring Telnet for Windows 2000 and Windows XP Installing Avaya Communication Manager Communication Manager installation Media server configuration Under Security, select Administrator Accounts Opening the Maintenance Web InterfaceCreating a super-user login Type susers in the login group field About the Avaya Installation Wizard Type sampcmd samp-update status and press Enter Running the Avaya Installation WizardInstalling Samp firmware Verifying the RMB IP information Configuring the modem Click Execute Ping Select Change Modem Setting and click Continue Enabling firewall settingsSelect Configure individual services and click Continue Enabling network time servers Enabling network time servers Configuring the NIC Checking LED activity on the dual NIC Configuring the NIC Disconnecting from the media server Click Continue IP interface translations Inputting initial system translations Adding media gateways Cabinet Cabinet Description Set the Ipsi Control of Port Networks field to enabled Enabling the Ipsi Saving translations Setting the alarm activation levelAdding the Ipsi to the system Type add ipserver-interface PNnumber and press Enter IP interface configuration Connecting to the IPSIs Ipsi address configuration Programming the Ipsi for static addressing Connecting the laptop directly to the Ipsi Type show control interface and press Enter Setting the Vlan and diffserv parameters Ipsi LED display for static address Programming the Ipsi for Dhcp addressing CLK IP interface configuration Verifying connectivity to the media server CLK Enabling control of the IPSIs Verifying that the IPSIs are translatedUpgrading the Ipsi firmware version if necessary Verifying the license status Install an S8500 Media Server as an LSP Configuring the media server as an LSP Select the Configure Individual Services Select Set IdentitiesSelect This is a local survivable processor LSP Administering the primary controller Enabling license server capability on a media gateway Installing and verifying the license on the new LSP Type stop -caf Type start -caf Resetting the S8500 LSP Click Advanced SettingOpening the TCP ports on the S8500 LSP Readministering media gateways to point to the LSP Verifying that the primary controller identifies the new LSP Postinstallation administration Verifying translationsList station List trunk-group List hunt-group Setting rules for daylight savings time Type change daylight-savings-rules and press Enter Setting locations if necessary Type change locations and press Enter Clearing and resolving alarms Verifying the date and the time Enabling and disabling the Ethernet switch ports Click Submit Changes Enabling alarms to Inads by way of a modem Backing up files to the compact flash media Enabling alarms to Inads by way of the Snmp module Before leaving the site Installation verification Testing the Ipsi circuit packTesting the license file S8500 LEDs S8500 front-panel LEDs Description Additional media server LED information Rear view of S8500B Media Server Avaya C360 Ethernet switch LEDs LAG LEDs on the Powerware 9125 UPS UPS LEDs TN2312BP Ipsi LEDs TN2312BP Ipsi circuit pack faceplate Ipsi LED display for a static IP address Connectivity status Appendix a Media server access Accessing the command line interface of the server with Backspace key area, select Control-H Connecting to the media server directly Cadlsrv3 KLC Connecting to the media server remotely over the network Connecting to the media server remotely over a modem Accessing the Maintenance Web Interface Click Launch Maintenance Web Interface Using the SAT command line prompt Logins for Avaya technicians and BusinessPartnersType of connection Procedure Configuring the network for Windows 2000 and XP Select Internet Protocol TCP/IPSubnet mask Setting the browser options for Internet Explorer Click on LAN settings, then AdvancedPage Appendix B Installation troubleshooting Problem Possible solution Ping 192.11.13.6 and press Enter Dhcp Press Enter Problem Possible solution Index Directly Remotely over modem Remotely over network Ipsi Enabling Setting version