Banner L-GAGE manual GAGEQ45UR High-Gain Controllers, GAGEQ45UR Remote Sensors Specifications

LIGHT GAUGING
LABEL&
ULTRASONIC
SLOT
LIGHT		lUMINESCENCE
MEASURING
	SCREENS
&
COLOR
TEMPERATURE
LIGHT-TO-
PICK
RADAR

MEASUREMENT & INSPECTION

U-GAGE®Q45UR High-Gain Controllers

Product P/N	Version
63060	Q45UR3BA63CQ6-63060	Discrete
63667	Q45UR3LIU64CQ6-63667	Analog

NOTE: Special High-Gain controllers are available for small object detection. Contact factory for more information.

U-GAGE®Q45UR Remote Sensors Specifications

Supply Voltage and Current	Discrete: 12 to 24V dc (10% max. ripple); 100 mA (exclusive of load)
	Analog: 15 to 24V dc (10% max. ripple); 100 mA (exclusive of load)
Ultrasonic Frequency	400 kHz
Supply Protection Circuitry	Protected against reverse polarity and transient voltages
Output Protection Circuitry	Both outputs are protected against continuous overload and short circuit
Output Rating	Discrete: 150 mA max. (each output)
	OFF-state leakage current: less than 25 µA at 24V dc
	ON-state saturation voltage: less than 1.5V at 10 mA; less than 2.0V at 150 mA
	Analog: Voltage sourcing: 0 to 10V dc, 10 mA max.
	Current sourcing: 4 to 20 mA, 1 to 500 Ω impedance
Output Configuration	Discrete: Bipolar: One current sourcing (PNP) and one current sinking (NPN) open collector transistor
	Analog: One voltage sourcing and one current sourcing; one or the other output is enabled by internal
	programming switch #2
Performance Specifications	Discrete: Response Speed:	40 or 160 milliseconds (switch selectable)
	Repeatability*:	±0.2% of measured distance
	Temperature stability: ±0.03% of the window limit positions per ° C from 0° to 50° C
		(±0.05% per ° C over remainder of operating temperature range)
	Sensing window width: 5 to 200 mm, when independent near and far limits are taught; 1, 2, 3,
	Hysteresis:	or 4 mm (switch selectable), when a sensing distance set point is taught
		0.5 mm
	Ultrasonic beam angle: ±3.5˚
	Analog: Response Speed:	10 to 320 milliseconds (2 to 64 cycles) selectable
	Resolution*:	0.2% of sensing distance at 320 milliseconds response
	Linearity*:	0.4% of sensing distance at 10 milliseconds response
		1% of full scale
	Temperature stability: ±0.03% of sensing distance per ° C from 0° to 50° C
		(±0.05% per ° C over remainder of operating temperature)
	Ultrasonic beam angle: ±3.5˚
	* Repeatability and analog resolution and linearity are specified using a 50 x 50 mm aluminum plate
	at 22° C under fixed sensing conditions (Analog: using the 4 to 20 mA output @ 15V dc)
Response Curves	See chart RC-6 on page 516.
Adjustments	Discrete: The following may be selected by a 4-position DIP switch located on top of the controller, beneath
	a transparent O-ring sealed acrylic cover and beneath the black inner cover
	Switch 1: Output normally open (output is energized when target is within sensing window limits),
	or normally closed (output is energized when target is outside sensing window limits)
	Switches 2 & 3: Sensing window size (1, 2, 3 or 4 mm)
	Switch 4: Response speed selection (40 or 160 milliseconds)
	Analog: Push-button TEACH-mode programming of window limits. The following may be selected by a
	4-position DIP switch located on top of the controller, beneath a transparent O-ring sealed acrylic
	cover and beneath the black inner cover
	Switch 1: Output slope: output value increases or decreases with distance
	Switch 2: Output mode: current output or voltage output
	Switches 3 & 4: Response to loss of echo
	Response Speed Adjustment: Single-turn potentiometer selects six response values from
	10 to 320 milliseconds
		More on
		next page

282 More information online at bannerengineering.com