Selecting Setup Pattern | Barco R9002249, R9002240 manual

Random Access Adjustment Mode

Selecting Setup Pattern

If an external source is connected to the projector, this menu will be displayed. Push the control disk up or down to highlight the desired setup pattern and then press ENTER.

Genlocked pattern : internally generated cross hatch pattern, locked on the external source.

Internal # pattern : internally generated cross hatch pattern and locked on internal generated sync signals. (No external source necessary)

ENTER continues to Random Access Adjustment Mode or Internal # Pattern Selection

EXIT returns to Path Selection menu ADJUST returns to Operational mode

If no external source is connected to the projector, the internal cross hatch pattern menu will be displayed.

Note: The menus in this manual are created for an external source, connected to one of the inputs, and the 'Genlocked Pattern' is selected.

Internal Cross Hatch Pattern

The Internal # pattern menu will be displayed if the internal cross hatch pattern has been selected or if no source is connected to the projector.

The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are custom programmable.

Push the control disk up or down to highlight the desired cross hatch frequency. Push the control disk to the left and to the right to scroll to another page. Press ENTER if the desired block is selected.

kHz/Hz
15.6/50	PAL/SECAM
15.7/60	NTSC
31.2/50	EDTV
31.5/60	IDTV
31.2/50	HDTV EUREKA
31.5/60	HDTV ATV
33.7/60	HDTV HIVISION
61.0/76	SUPER VGA 3

ENTER continues to the Random Access Adjustment Mode.

EXIT returns to the Setup Pattern Selection menu.

Choose a setup pattern from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 01

Select with or then <ENTER> <EXIT> to return.

INTERNAL # PATTERN
kHz / Hz
15.6/50	PAL/SECAM
15.7/60	NTSC
31.2/50	EDTV
31.5/60	IDTV
31.2/50	HDTV EUREKA
31.5/60	HDTV	ATV
	Select with	or
	scroll with	or
<ENTER> to accept
	<EXIT> to return

5975688 BARCOVISION 1609S 131097		6-3

Image 25

Barco R9002249, R9002240 owner manual Selecting Setup Pattern, Internal Cross Hatch Pattern

Contents

Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of Controls RCU control panel terminology Control panel terminology Local Keypad built in RCU Power Check AC Power mains Cord ConnectionSwitching On/Off Connections Pleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to port Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCU Projector Address How to use your RCU How to program an address into the RCU? How to display a projector address?Projector Address Controlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode Enter From next Internal Cross Hatch Pattern Selecting Setup Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Color Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Peaking Line Doubler option Port 2 Video or S-VideoColor Select Line Doubler on Focusing color select FocusingMidpoint focusing Top image focusing Horizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift Adjustment LEFT-RIGHT E-W Left-Right east-west Adjustments Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Blanking Blanking Adjustments Coarse Convergence Adjustment Convergence AdjustmentConvergence RED on Green Vertical Corners Fine Convergence Adjustment Random Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode Service Copy a block IdentificationCopy a Block Deleting block by block Deletion of blocksDeletion of all blocks Delete a Block Change Password Change passwordChange Language Run time Undo Midposition Set to midpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustment Gamma corrections G2 AdjustCRT run in cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeProjector Warm Up Input MESSAGES, Warnings and FailuresSource Projector Address Iris FAN Failed Wait Options Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler Kit Orbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card