Connecting a Composite Video source to port | Barco R9002249

Connections

Connecting a Composite Video source to port 1.

Composite video signals from a VCR, OFF air signal decoder, etc..

Video input selection :

with the RCU or the build in RCU : press digit button 1

* Note : if using the loop-through Video output, then set the Termination Switch to the "OFF" position.

Connecting a S-Video or Video source to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.

4 pin connector configurations:

For S-video:		For video:
Pin 1: earth(ground) luminance		Pin 1:	earth(ground) video
Pin 2: earth(ground) chrominance	3	Pin 2:	notconnected
Pin 3: luminance signal(Y)	1	Pin 3:	video signal
Pin 3: luminance signal(Y)		Pin 3:	video signal
1Vpp±3dB	2	Pin 4: notconnected
Pin 4: chrominance signal(C)	4
Pin 4: chrominance signal(C)
300mVpp±3dB

Input selection

with the RCU or the build in RCU : press digit button 2 Depending on the priority setting in the Picture Tuning menu, Video or S-Video can be displayed.

If the setting is not correct, start up the adjustment mode by pushing on th ADJUST key.

Select 'Random Access' and press ENTER.

Select 'Selected source' and press ENTER.

Highlight 'Picture Tuning' and press ENTER.

Highlight Port 2 : Video and press ENTER to toggle between VIDEO or S-VIDEO.

Press EXIT to return.

Press ADJUST to return to operational mode.

*Note: When using the Port 2 loop-through output, set the Termination Switch in the "OFF" position.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

Source 02 Choose a setup pattern

from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 02

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT
ORBITING
CONTR	PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PORT2 : S-VIDEO

LINE DOUBLER : ON

Select with or <ENTER> to accept <EXIT> to return.

5975688 BARCOVISION 1609S 131097		3-3

Image 13

Barco R9002249, R9002240 Connecting a Composite Video source to port, Connecting a S-Video or Video source to port

Contents

Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of Controls RCU control panel terminology Control panel terminology Local Keypad built in RCU Power Check AC Power mains Cord ConnectionSwitching On/Off Connections Pleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to port Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCU Projector Address How to use your RCU How to program an address into the RCU? How to display a projector address?Projector Address Controlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode Enter From next Internal Cross Hatch Pattern Selecting Setup Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Color Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Peaking Line Doubler option Port 2 Video or S-VideoColor Select Line Doubler on Focusing color select FocusingMidpoint focusing Top image focusing Horizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift Adjustment LEFT-RIGHT E-W Left-Right east-west Adjustments Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Blanking Blanking Adjustments Coarse Convergence Adjustment Convergence AdjustmentConvergence RED on Green Vertical Corners Fine Convergence Adjustment Random Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode Service Copy a block IdentificationCopy a Block Deleting block by block Deletion of blocksDeletion of all blocks Delete a Block Change Password Change passwordChange Language Run time Undo Midposition Set to midpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustment Gamma corrections G2 AdjustCRT run in cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeProjector Warm Up Input MESSAGES, Warnings and FailuresSource Projector Address Iris FAN Failed Wait Options Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler Kit Orbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card