Horizontal Size Adjustment | Barco R9002249, R9002240 manual

Random Access Adjustment Mode

Seagull Correction

Use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull) on top and bottom of the image is visible, proceed to the seagull correction. Due to interaction, it is possible that the top and bottom bow have to be readjusted after adjusting the seagull correction to obtain an improved image. The default value on the bar scale of this correction is 50.

Push the control disk up or down to select the 'Seagull Correction' and press ENTER to select.

Eliminate teh deformation by pushing the control disk upwards or downwards until a straight line is obtained.

ENTER will return to Top-Bottom adjustment menu EXIT will return to Geometry menu

Horizontal Size Adjustment

Push the control disk up or down to highlight H SIZE on the Geometry menu and then press ENTER.

ENTER will select horizontal size adjustment

EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode

Adjust the horizontal size by the control disk to the right or to the left until the exact image width is obtained.

Note :

-if the internal # pattern was selected, this pattern remains on the screen.

-if the genlocked pattern was selected, the external source will be displayed.

A bar scale and a numeric indicator help to gauge the horizontal size adjustment.

Hint : In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small horizontal size setting.

EXIT will return to Geometry

GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM(N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with	or
then <ENTER>
<EXIT>	TOP-BOTTOM(N-S)

	H CENTERLINE BOW
	H CENTERLINE SKEW
	TOP KEYSTONE
	TOP BOW
	BOTTOM KEYSTONE
	BOTTOM BOW
	SEAGULL CORRECTION
	Select with	or
	then <ENTER>
	<EXIT> to	return.

GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with	or
then <ENTER>
<EXIT> to	return.
	H SIZE
	70

H size too large

Ideal image width

H size too small

5975688 BARCOVISION 1609S 131097		6-13

Image 35

Barco R9002249, R9002240 owner manual Horizontal Size Adjustment

Contents

Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of Controls RCU control panel terminology Control panel terminology Local Keypad built in RCU Connections AC Power mains Cord ConnectionPower Check Switching On/Off Remaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to port RED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCU Projector Address How to use your RCU Address How to display a projector address?How to program an address into the RCU? Projector Brightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Line Doubler on Port 2 Video or S-VideoLine Doubler option Color Select Top image focusing FocusingFocusing color select Midpoint focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift Adjustment LEFT-RIGHT E-W Left-Right east-west Adjustments Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Blanking Blanking Adjustments RED on Green Convergence AdjustmentCoarse Convergence Adjustment Convergence Vertical Corners Fine Convergence Adjustment Random Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service mode Copy a Block IdentificationCopy a block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocks Run time Change passwordChange Password Change Language Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustment CRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycle Projector Warm Up CRT Drive ModeCRT Drive Mode Projector Address MESSAGES, Warnings and FailuresInput Source Iris FAN Failed Wait Options Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card