Adjustment Blocks and Source Numbers | Barco R9002240, R9002249

Adjustment Blocks and Source Numbers 90-99

The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source number is selected, the alternate block of adjustment data is in use and may be modified via the adjust mode of the projector. The alternate adjustment block is automatically stored.

Follow the steps below to create a second adjustment block for a source between 0 and 9.

1.Select the source between 0 and 9 that the second adjustment block is to be created for.

2.Select the corresponding source number between 90 and 99. The adjustment block for the source number between 0 and 9 is copied to the corresponding source number between 90 and 99.

3.Enter the adjust mode and make any desired changes (geometry, convergence, sync fast/slow, enhanced blue on/off) to the second adjustment block.

4.Exit the adjust mode.

Note : the above also applies to source number 1 - 5 and 91 - 95 of a stand alone projector (no RCVDS)

B-2		5975688 BARCOVISION 1609s 131097

Image 58

Barco R9002240, R9002249 owner manual Adjustment Blocks and Source Numbers

Contents

Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel Terminology Control panel terminology Local Keypad built in RCU RCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check Connections Pleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to port Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU Controlling How to use your RCU Projector Address Projector How to display a projector address?How to program an address into the RCU? Address Controlling chained projectors Analog Picture ControlsBrightness Start UP of the Adjustment Mode Adjustment Mode Start Up of the Adjustment Mode Overview Random Access Adjustment mode Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Enter From next Selecting Setup Pattern Internal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Color Select Port 2 Video or S-VideoLine Doubler option Line Doubler on Midpoint focusing FocusingFocusing color select Top image focusing Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift Adjustment Correct raster position Wrong raster position Left-Right east-west Adjustments LEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment Size Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Blanking Convergence Convergence AdjustmentCoarse Convergence Adjustment RED on Green Fine Convergence Adjustment Vertical Corners Random Access Adjustment Mode Overview flowchart Service mode Service ModeStarting up the Service mode Service Copy a block IdentificationCopy a Block Deletion of all blocks Deletion of blocksDeleting block by block Delete a Block Change Language Change passwordChange Password Run time Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections CRT RUN in Cycle CRT Drive Mode CRT Drive ModeProjector Warm Up Source MESSAGES, Warnings and FailuresInput Projector Address Wait Iris FAN Failed Options Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler Kit Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card