Barco R9002249, R9002240 manual

Orbiting

Adjustment procedure multiple projector installations :

Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum.

Default setting of the Master projectorn see 'Stand-Alone projector'.

Highlight 'ADJUST DEVIATION' by pushing the control stick forward or backward and press ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation adjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH		OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH		OR
HORIZONTAL	WITH	OR
<EXIT> to	return.

Horizontal

orbitampl.

60

Vertical

orbitampl.

60

5975628 BARCOGRAPHICS 1209s 010797		A-3

Image 55

Barco R9002249, R9002240 owner manual Adjustment procedure multiple projector installations

Contents

Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of Controls RCU control panel terminology Control panel terminology Local Keypad built in RCU Connections AC Power mains Cord ConnectionPower Check Switching On/Off Pleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to port Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCU Projector Address How to use your RCU Address How to display a projector address?How to program an address into the RCU? Projector Controlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Line Doubler on Port 2 Video or S-VideoLine Doubler option Color Select Top image focusing FocusingFocusing color select Midpoint focusing Horizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift Adjustment LEFT-RIGHT E-W Left-Right east-west Adjustments Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Blanking Blanking Adjustments RED on Green Convergence AdjustmentCoarse Convergence Adjustment Convergence Vertical Corners Fine Convergence Adjustment Random Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service mode Copy a block IdentificationCopy a Block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocks Run time Change passwordChange Password Change Language Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustment CRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycle CRT Drive Mode CRT Drive ModeProjector Warm Up Projector Address MESSAGES, Warnings and FailuresInput Source Iris FAN Failed Wait Options Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card