Wait, Iris FAN Failed | Barco R9002240, R9002249 manual

Messages, warnings and failures

FAILURE

RCVDS com-

munication

error

FAILURE

IRIS commu-

nication

error

WAIT

starting

up

IRIS

FAN FAILED

Projector

will

switch off

Serial communication error be- tween the RCVDS and the projec- tor.

Communication error between IRIS 800 and the projector. Call a quali- fied service technician.

Message during the start up of the IRIS. Message will disappear when the IRIS is ready to accept com- mands.

Message when one of the fans are not working anymore. Projector switches to stand-by

8-2		5975688 BARCOVISION 1609s 131097

Image 50

Barco R9002240, R9002249 owner manual Wait, Iris FAN Failed

Contents

Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel Terminology Control panel terminology Local Keypad built in RCU RCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check Connections Remaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a Composite Video source to port Connecting a S-Video or Video source to port RED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Battery installation in the RCU Controlling How to use your RCU Projector Address Projector How to display a projector address?How to program an address into the RCU? Address Brightness Analog Picture ControlsControlling chained projectors Start UP of the Adjustment Mode Adjustment Mode Start Up of the Adjustment Mode Overview Random Access Adjustment mode Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Enter From next Selecting Setup Pattern Internal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Color Select Port 2 Video or S-VideoLine Doubler option Line Doubler on Midpoint focusing FocusingFocusing color select Top image focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Raster Shift Adjustment Correct raster position Wrong raster position Left-Right east-west Adjustments LEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment Size Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Blanking Convergence Convergence AdjustmentCoarse Convergence Adjustment RED on Green Fine Convergence Adjustment Vertical Corners Random Access Adjustment Mode Overview flowchart Service mode Service ModeStarting up the Service mode Service Copy a Block IdentificationCopy a block Deletion of all blocks Deletion of blocksDeleting block by block Delete a Block Change Language Change passwordChange Password Run time Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections CRT RUN in Cycle Projector Warm Up CRT Drive ModeCRT Drive Mode Source MESSAGES, Warnings and FailuresInput Projector Address Wait Iris FAN Failed Options Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler Kit Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card