From next | Barco R9002240, R9002249 guide

Random Access Adjustment Mode

From next page

From next page

RANDOM ACCESS

ADJUSTMENTMODE

SETUPPATTERNSELECTION

H SIZE

V LINEARITY

V SIZE

BLANKING

						GREENONLY
						GREENONLY


	CONVERGENCE					REDONGREEN





						BLUEONGREEN
						BLUEONGREEN


						RED
						RED


	FOCUSING					GREEN
	FOCUSING					GREEN


						BLUE
						BLUE


						RED
						RED


						GREEN
						GREEN


						BLUE
						BLUE
	COLORSELECT
						REDANDGREEN
						REDANDGREEN


						BLUE AND GREEN
						BLUE AND GREEN


						RED AND BLUE
						RED AND BLUE

ORBITING

CONTRASTMODULATION

SOFTEDGECORRECTION

TOP

BOTTOM

LEFT

RIGHT

6-2		5975688 BARCOVISION 1609S 131097

Image 24

Barco R9002240, R9002249 owner manual From next

Contents

Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel Terminology Control panel terminology Local Keypad built in RCU RCU control panel terminology AC Power mains Cord Connection Power CheckSwitching On/Off Connections Signal Input Connection to the Projector Pleaseuse Exitto Leave this ProcedureRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to port Connecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5RED Green Blue Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the projector Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU Controlling How to use your RCU Projector Address How to display a projector address? How to program an address into the RCU?Projector Address Analog Picture Controls Controlling chained projectorsBrightness Start UP of the Adjustment Mode Adjustment Mode Start Up of the Adjustment Mode Random Access Adjustment Mode Starting-Up the Random Access Adjustment modeOverview Random Access Adjustment mode Enter From next Selecting Setup Pattern Internal Cross Hatch Pattern Random access adjustment mode selection menu Picture TuningColor Balance Color Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Peaking Port 2 Video or S-Video Line Doubler optionColor Select Line Doubler on Focusing Focusing color selectMidpoint focusing Top image focusing Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift Adjustment Correct raster position Wrong raster position Left-Right east-west Adjustments LEFT-RIGHT E-W Seagull correction Left Side CorrectionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment Size Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Blanking Convergence Adjustment Coarse Convergence AdjustmentConvergence RED on Green Fine Convergence Adjustment Vertical Corners Random Access Adjustment Mode Service Mode Starting up the Service modeOverview flowchart Service mode Service Identification Copy a blockCopy a Block Deletion of blocks Deleting block by blockDeletion of all blocks Delete a Block Change password Change PasswordChange Language Run time Set to midposition Undo MidpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle CRT RUN in Cycle CRT Drive Mode CRT Drive ModeProjector Warm Up MESSAGES, Warnings and Failures InputSource Projector Address Wait Iris FAN Failed Options Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Orbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave Toggle Adjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks and Source Numbers 90 Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card