Convergence Adjustment, RED on Green | Barco R9002240, R9002249

Random Access Adjustment Mode

Convergence Adjustment

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image.

Start with the Coarse convergence adjustments and finalise with the Fine convergence adjustment.

RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
CONVERGENCE
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
FINE ADJUSTMENT
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
Select with	or
then <ENTER>
<EXIT> to	return.

The screen area is divided into 25 areas.	25	23	9	15	17
	25	23	9	15	17

	24	22	8	14	16

	5	4	1	2	3

	20	18	6	10	12

	21	19	7	11	13

Coarse Convergence Adjustment.

Highlight 'Red on green' under the coarse convergence item and press ENTER. The coarse convergence menu will be displayed. The following items are possible :

-Horizontal sides : adjust the vertical lines, within a certain area, on both sides without influencing the lines on the middle of the image.

-Vertical corners : adjust the horizontal lines in the four corners, within a certain area, without influencing the middle of the image.

Repeat for 'blue on green'

CONVERGENCE

COARSE ADJUSTMENT

RED ON GREEN

BLUE ON GREEN

FINE ADJUSTMENT

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

COARSE CONVERGENCE

HORIZONTAL SIDES

VERTICAL CORNERS

Select with	or
then <ENTER>
<EXIT> to	return.

Horizontal sides

Highlight 'Horizontal lines' and press ENTER to start the adjustment. To make a coarse adjustment of the red or blue vertical lines in zone 3 and 5 simultaneously.

B G RB G R

Hint :

-look to the end of scan and adjust until the red or the blue vertical lines are on the green lines or as close as possible to the green lines.

-during these adjustments, the horizontal convergence adjustments in zones 2, 3, 4 and 5 will be set to midposition (barscale 50).

COARSE CONVERGENCE

HORIZONTAL SIDES VERTICAL CORNERS

Select with	or
then <ENTER>
<EXIT> to	return.

6-16		5975688 BARCOVISION 1609S 131097

Image 38

Barco R9002240, R9002249 owner manual Coarse Convergence Adjustment, RED on Green, Horizontal Sides Vertical Corners

Contents

Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel Terminology Control panel terminology Local Keypad built in RCU RCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check Connections Remaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a Composite Video source to port Connecting a S-Video or Video source to port RED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Battery installation in the RCU Controlling How to use your RCU Projector Address Projector How to display a projector address?How to program an address into the RCU? Address Brightness Analog Picture ControlsControlling chained projectors Start UP of the Adjustment Mode Adjustment Mode Start Up of the Adjustment Mode Overview Random Access Adjustment mode Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Enter From next Selecting Setup Pattern Internal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Color Select Port 2 Video or S-VideoLine Doubler option Line Doubler on Midpoint focusing FocusingFocusing color select Top image focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Raster Shift Adjustment Correct raster position Wrong raster position Left-Right east-west Adjustments LEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment Size Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Blanking Convergence Convergence AdjustmentCoarse Convergence Adjustment RED on Green Fine Convergence Adjustment Vertical Corners Random Access Adjustment Mode Overview flowchart Service mode Service ModeStarting up the Service mode Service Copy a Block IdentificationCopy a block Deletion of all blocks Deletion of blocksDeleting block by block Delete a Block Change Language Change passwordChange Password Run time Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections CRT RUN in Cycle Projector Warm Up CRT Drive ModeCRT Drive Mode Source MESSAGES, Warnings and FailuresInput Projector Address Wait Iris FAN Failed Options Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler Kit Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card