Change password, Change Language, Run time | Barco R9002240 guide

Service Mode

Change password

This item is password protected.

Highlight 'change password' with the control disk and press ENTER.

The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control disk to the left or to the right to select the digits to be changed. Use the numeric keys to enter the new digits.

Press ENTER to save the new password. Before saving the new password, a confirmation screen will be displayed.

Press EXIT to return to the Service menu without saving the new password.

When the displayed password is correct, press ENTER to save. If not correct, press EXIT to cancel the saving.

SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
	PASSWORD
Enter new password :
	0 0 0 0
Use	and	to select,
and	reprogram
with	numeric	keys.

CHANGE PASSWORD

Password will be reprogrammed as xxxx

<ENTER> to confirm <EXIT> to cancel

Change Language

The 'Change Language' function offers the possibility to change the language of the screen menus to :

-English

-Spanish

-French

-German

therefore, pusj the control disk up or down to highlight 'Change language' and press ENTER to select the language menu.

Push the control disk up or down to select the desired language and press ENTER to change the language.

Run time

Highlight 'run time' with the control disk and press ENTER to display the amount of time the projector has played since its first start up at the factory.

Note : all projectors leave the factory after a burn-in period of approximately 100 hours.

Press EXIT to return the service mode menu.

SERVICE MODE

IDENTIFICATION

COPY A BLOCK

DELTE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUN TIME

SET TO MIDPOSITION

CONVERGENCE MID

DYNAMIC ASTIGMATISM

MORE...

LANGUAGE
ENGLISH
ESPAÑOL
FRANCAIS
DEUTSCH
Select new	language
with	or
then <ENTER>
<EXIT> to	return.

SERVICE MODE

IDENTIFICATION

COPY A BLOCK

DELTE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUN TIME

SET TO MIDPOSITION

RUN TIME

105h

7-4		5975688 BARCOVISION 1609s 131097

Image 44

Barco R9002240, R9002249 owner manual Change password, Change Language, Run time, Change Password

Contents

Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel Terminology Control panel terminology Local Keypad built in RCU RCU control panel terminology AC Power mains Cord Connection Power CheckSwitching On/Off Connections Remaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a Composite Video source to port Connecting a S-Video or Video source to port RED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Battery installation in the RCU Controlling How to use your RCU Projector Address How to display a projector address? How to program an address into the RCU?Projector Address Brightness Analog Picture ControlsControlling chained projectors Start UP of the Adjustment Mode Adjustment Mode Start Up of the Adjustment Mode Random Access Adjustment Mode Starting-Up the Random Access Adjustment modeOverview Random Access Adjustment mode Enter From next Selecting Setup Pattern Internal Cross Hatch Pattern Random access adjustment mode selection menu Picture TuningColor Balance Color Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Peaking Port 2 Video or S-Video Line Doubler optionColor Select Line Doubler on Focusing Focusing color selectMidpoint focusing Top image focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Raster Shift Adjustment Correct raster position Wrong raster position Left-Right east-west Adjustments LEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment Size Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Blanking Convergence Adjustment Coarse Convergence AdjustmentConvergence RED on Green Fine Convergence Adjustment Vertical Corners Random Access Adjustment Mode Service Mode Starting up the Service modeOverview flowchart Service mode Service Copy a Block IdentificationCopy a block Deletion of blocks Deleting block by blockDeletion of all blocks Delete a Block Change password Change PasswordChange Language Run time Set to midposition Undo MidpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle CRT RUN in Cycle Projector Warm Up CRT Drive ModeCRT Drive Mode MESSAGES, Warnings and Failures InputSource Projector Address Wait Iris FAN Failed Options Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Orbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave Toggle Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card