Random Access Adjustment Mode, Enter | Barco R9002249, R9002240

Random Access Adjustment Mode

6RANDOM ACCESS ADJUSTMENT MODE

Starting-Up the Random Access Adjustment mode.

Push the control disk up or down to highlight "RANDOM ACCESS" and then press

ENTER.

Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode.

ENTER continues to Setup Pattern Selection

EXIT returns to Operational mode

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS INSTALLATION SERVICE

IRIS

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Overview 'Random Access Adjustment' mode

PICTURETUNING

RANDOM ACCESS	GEOMETRY
ADJUSTMENTMODE

SETUPPATTERNSELECTION

COLOR BALANCE

SYNC

PEAKING

CLAMPTUNING

LINEDOUBLER

PORT2

H PHASE

RASTERSHIFT

LEFT-RIGHT (E-W)

LEFTSIDECORRECTIONS

TOP-BOTTOM (N-S)

VCENTERLINEBOW

VCENTERLINESKEW

SIDEBOW

SIDEKEYSTONE

SEAGULLCORRECTION

LEFTKEYSTONE

LEFT BOW

HCENTERLINEBOW

HCENTERLINESKEW

TOPKEYSTONE

TOPBOW

BOTTOMKEYSTONE

BOTTOMBOW

SEAGULLCORRECTION

To next page

To next page

5975688 BARCOVISION 1609S 131097

6-1

Image 23

Barco R9002249, R9002240 owner manual Random Access Adjustment Mode, Starting-Up the Random Access Adjustment mode, Enter

Contents

Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of Controls RCU control panel terminology Control panel terminology Local Keypad built in RCU Connections AC Power mains Cord ConnectionPower Check Switching On/Off Remaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to port RED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCU Projector Address How to use your RCU Address How to display a projector address?How to program an address into the RCU? Projector Brightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Sync Fast/Slow AdjustmentClamp Tuning Peaking Line Doubler on Port 2 Video or S-VideoLine Doubler option Color Select Top image focusing FocusingFocusing color select Midpoint focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift Adjustment LEFT-RIGHT E-W Left-Right east-west Adjustments Left Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Blanking Blanking Adjustments RED on Green Convergence AdjustmentCoarse Convergence Adjustment Convergence Vertical Corners Fine Convergence Adjustment Random Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service mode Copy a Block IdentificationCopy a block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocks Run time Change passwordChange Password Change Language Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustment CRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycle Projector Warm Up CRT Drive ModeCRT Drive Mode Projector Address MESSAGES, Warnings and FailuresInput Source Iris FAN Failed Wait Options Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card