Hardware Installation Power Connectors | Belkin PM11-UL/RAMA

2

Hardware Installation

2.6.21 Power Connectors

+12V power
(ATXP1)
2	1
4	3
	10	20
	1	11
	ATX power
		(J26)

We recommend that you use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1. Connect the ATX12V power supply’s 20-pin ATX main power connector and 4-pin +12V power connector to J26 and ATXP1 respectively.

The 4-pin +12V power connector enables the delivery of more +12VDC current to the processor’s Voltage Regulator Module (VRM).

The mainboard requires a minimum of 250 Watt power supply to operate.Your system configuration (amount of memory, add-in cards, peripherals, etc.) may exceed the minimum power requirement. To ensure that adequate power is provided, use a 300 Watt (or greater) power supply.

52

Image 52

Belkin PM11-UL/RAMA, PM11-EL/RAMA, PM11-EC/RAMA manual Hardware Installation Power Connectors

Contents

PM11-EC/RAMA PM11-EL/RAMA PM11-UL/RAMA 55600206 Copyright All Rights Reserved FCC and DOC Statement on Class B Mainboard Table of Contents Appendix a Using the Suspend to Appendix C TroubleshootingSupported Softwares Function Features and Specifications FeaturesChipset Processor Onboard Audio Features Onboard LAN Features PM11-EL/RAMA and PM11-UL/RAMA onlyOnboard Graphics Features Introduction Connectors ATX Double Deck Ports PC 99 color-coded connectorsOnboard Integrated Media Reader Smart I/O PM11-UL/RAMA only IrDA Interface PCI Bus Master IDE ControllerUSB Ports Dual Function Power Button System Health Monitor FunctionsIntelligence Desktop Management Interface DMI Wake-On-LAN Wake-On-RingWake-On-PS/2 Keyboard/Mouse RTC Timer to Power-on the System Wake-On-USB Keyboard/Mouse AC Power Failure Recovery Package ChecklistVirus Protection Hardware Installation Mainboard Layout Hardware Installation Supports onboard audio and onboard LAN Supports onboard audio, onboard LAN, USB 2.0 and Smart I/O System Memory Hardware Installation Installing the DIM Module Jumper Settings for Clearing Cmos Data Clear Cmos Data Jumper JP2 If you encounter the following Hardware Installation On Disable VCC power Jumper Settings for Wake-On-PS/2 Keyboard/MouseWake-On-PS/2 Keyboard/Mouse Jumper JP1 Wake-On-USB 2.0 Keyboard/Mouse J13 and J14 Ports and Connectors Connecting the Serial PortsSerial Ports Serial Port Hardware Installation Hardware Installation 2 PS/2 Mouse and PS/2 Keyboard Ports PS/2 Mouse PS/2 Keyboard Hardware Installation Parallel Port Setting Function Standard Parallel Port One direction onlyAllows parallel port to operate Rate Hardware Installation Floppy Disk Drive Connector Connecting the Floppy Disk Drive Cable Hardware Installation IDE Disk Drive Connector Connecting the IDE Disk Drive Cable Adding a Second IDE Disk Drive Hardware Installation Universal Serial Bus Ports 6.1 PM11-EC/RAMA and PM11-EL/RAMA 6.2 PM11-UL/RAMA UP2 USB 1.1 J17 Pin FunctionFunction 5VDul Data+ Ground Key RJ45 LAN Hardware Installation VGA Port VGA Port Hardware Installation IrDA Connector Pin Function Hardware Installation CPU Fan Connector Hardware Installation Chassis Fan Connector On/Off +12V Sense Hardware Installation Chip Fan Connector Hardware Installation Game/MIDI Port Hardware Installation Audio Jacks Mic+ Ground Mic Power AuDVcc Avcc AuDROutFront Audio J3 AuDLOut Connect a microphone to the mic-in jack Onboard Audio Jacks CN3Front Audio J3 Left audio channel Ground Right audio channel Hardware Installation Internal Audio ConnectorsAUX-in and CD-in Hardware Installation 16 S/PDIF-out Connector Spdif Hardware Installation Smart I/O Connectors PM11-UL/RAMA only Optional Smart I/O Drive Memory Stick Interface Smart Card Interface Pin FunctionSecure Digital Memory Card Interface Hardware Installation Wake-On-LAN Connector +5VSB Hardware Installation Wake-On-Ring Connector RI# Dimm Standby Power LED Hardware Installation Dimm and PCI Standby Power LEDsPCI Standby Power LED Hardware Installation Power Connectors +12V +5V +12V Power Connector Pin Function Ground ATX Main Power Connector Pin Function 12V Ground +5VGround +5V Hardware Installation Front Panel Connectors PWR-LED Power/Standby LED When you press Del, the main menu screen will appear Standard Cmos FeaturesBasic Input/Output System Award Bios Setup Utility DateTime IDE HDD Auto Detection Access Mode IDE Primary/Secondary Master/SlaveCapacity Drive a and Drive B Halt On Base MemoryExtended Memory Total Memory Award Bios Setup Utility Advanced Bios Features Virus Warning Quick Power On Self Test CPU L1 & L2 CacheCPU L2 Cache ECC Checking Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Setting Typematic Delay Msec Video Bios Shadow Security OptionOS Select for Dram 64MB Small LogoEPA Show Award Bios Setup Utility Advanced Chipset Features Dram Clock/Drive ControlCurrent FSB Frequency Current Dram Frequency Dram Clock Dram TimingSdram CAS Latency Bank Interleave Dram Command Rate AGP ModeActive to Precharge Tras Active to CMD Trcd PCI Delay Transaction AGP Master 1 WS ReadCPU to PCI Write Buffer PCI Master 0 WS Write Options are Enabled and Disabled Video RAM CacheableVGA Share Memory Size FB Address Conversion Award Bios Setup Utility Integrated Peripherals IDE Prefetch ModeVIA OnChip IDE Device OnChip IDE Channel 0 and OnChip IDE Channel VIA-3058 AC97 Audio VIA OnChip PCI DeviceOnboard LAN PM11-EL/RAMA and PM11-UL/RAMA only Onboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortSC Port Address/IRQ PM11-UL/RAMA only MS Port Address/IRQ PM11-UL/RAMA only Uart Mode Select IR Transmission DelayUR2 Duplex Mode Use IR Pins Parallel Port Mode EPP Mode SelectECP Mode Use DMA Game Port Address IDE HDD Block Mode Onboard LAN Boot ROM PM11-EL/RAMA and PM11-UL/RAMA onlyOnChip USB1.1 Controller USB Keyboard Support Acpi Function Award Bios Setup Utility Power Management SetupAcpi Suspend Type Power Management Option HDD Power DownSuspend Mode Video Off Option Run Vgabios if S3 Resume Modem Use IRQSoft-Off by Pwrbtn PWR Lost Resume State IRQ/Event Activity Detect PS2KB Wakeup SelectUSB Resume from S3 PCI Master Resume on PCI Event Resume on AlarmResume On LAN/Ring Resume Time hhmmss Date of MonthIRQs Activity Monitoring Award Bios Setup Utility 6 PnP/PCI Configurations PNP OS InstalledReset Configuration Data Resources Controlled By IRQ Resources PCI/VGA Palette SnoopAssign IRQ for VGA Assign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 3 Use IRQ CPU Warning Temperature Award Bios Setup Utility PC Health StatusThese fields show the voltage of the processor +3.3V, +5V, +12V, -12V, -5V, Vbatv and 5VSBV Award Bios Setup Utility Frequency/Voltage Control CPU ClockAuto Detect PCI/DIMM Clk Spread Spectrum CPU Clock Ratio This field is used to select the CPU’s frequency ratio Award Bios Setup Utility Load Fail-Safe Defaults Load Optimized Defaults Award Bios Setup Utility Set Supervisor Password Set User Password Award Bios Setup Utility Save & Exit Setup Updating the BiosExit Without Saving Desktop Management Interface DMI Running the DMI Utility Supported Software Using the DMI Utility Edit DMI Load DMI File Supported Software Add DMISave DMI File Hardware Monitor VIA Service PackSupported Software VIA Service Pack Installation Notes Audio Drivers and Software Applications VIA USB 2.0 Driver PM11-UL/RAMA only Graphics DriversWinbond Smart I/O Drivers PM11-UL/ Rama only Drivers and Utilities Installation Notes Microsoft DirectX 8.1 Driver Appendix a Using the Suspend to RAM Function Using the Suspend to RAM Function Using the Suspend to RAM Function 101 102 Cmos battery is no longer functional. It should be replaced Error MessagesPost Beep System Error Message Troubleshooting Checklist Monitor/Display Power Supply TroubleshootingFloppy Drive Troubleshooting Hard Drive Hard disk failure Keyboard Troubleshooting Serial PortMainboard