Default Settings | Bosch Appliances MIC412 instruction

MIC412TI and MIC412TF Camera Installation and Operation Manual

Self Diagnosis

This function is for future products and does not work with the MIC400 or MIC412.

Default Settings

The Default Settings tab reads and sets settings from the following sections:

-Manual Control Auxiliaries

-General Settings

-Auto Home Controls

-Multi Alarm Settings

-Lens Recalibration

-Frame Integration Settings

-All Thermal controls

All other settings will not be saved, loaded, downloaded or set through the following controls.

EN 31

Get Current MIC Settings

This downloads the current status of each of the settings from the MIC and loads it into the text boxes and radio buttons on Camset. This provides an easy way of viewing the current setup of each MIC and also a way of copying the settings from one into the next.

Save Current MIC Settings

This option will first prompt for a file location and then store the current state of all the options outlined above to an XML file which can then be loaded at a later date back into Camset as a standard for a specific site.

Load Settings into Camset

This will prompt to open an XML file as saved above. Only valid Camset Default XML files will work.

Set Current Settings to MIC

This will go through each of the settings above except for thermal, and send out the commands to the MIC to set it up as Camset displays. This may take a few seconds as there are several commands involved in this process.

Upload Default Options

At the end of this there are 2 extra options for defaults, Clear SS and NDZ will clear any saved Soft Stops and Non-Dwell Zones and then Find End Stops. These options may be used to completely set up a MIC after it has been reprogrammed to a new protocol.

Bosch Security Systems

Issue 8

Image 31

Bosch Appliances MIC412 operation manual Default Settings

Contents

MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Appendices Glossary of Terms Introduction MIC412 Camera Versions MIC 412 Power Supply Unit Versions and Options Wiper FeaturesPackaging Contents MIC 412 Options Installation Environment Bosch Security Systems Issue Key to MIC-PMB drawing Associated Equipment and Typical Installations Installation Instructions Hardware Installation Lightning Protection Earthing of the MIC 412 cameraElectrical Connections PCB Earth Link MIC 412TI and MIC 412TF Power Supply UnitsPower Supply Layout and Connections MIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL Table D -Telemetry Connections to HD3, HD4 and HD5 HD3 Rating for 115v Primary Terminal Box ConnectorTerminal Box ID Marking Fuse Fuse function Rating for 240v Primary Commissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor Connecting the MIC 412 to the PCConnecting the Greenwich Adaptor Table G Connecting the Greenwich Adaptor Connecting the MIC-USB485CVTR, USB to RS485 Converter Table I Camera Interface Control Settings DIP SwitchCamset Tabs Wire RS485 Wire RS422 HD4 or HD5 MIC-USB485CVTR and Universal Camset Software Installation Standard Controls Boot MessagesMIC Settings Commissioning the MIC412 through Universal Camset Camset Settings Manual Control Pan, Tilt and Zoom Controls Auxiliaries Preset PositionsIris Controls Focus Controls Tour Controls Preset ToursPattern Tours Clear MIC SetupsSoft Stops and Non Dwell Zones Non-Dwell Zone General Settings Other controls Auto Home Controls Default Settings Relay State, Activation and Re-arm Multi Alarm SettingsLearn Alarm Positions Frame Integration Settings Privacy Controls Privacy and Captions Privacy Calibration Captions Gain and Auto Gain Modes FFC Mode and SettingsThermal Shutter Open/Close Clear All Statistics Advanced SettingsTemperature and Humidity Timers Upload Eeprom From File Eeprom CopierOnly Download Eeprom To File Matrix Controls Manual and Preset / Goto ControlsPOT Test Menu Controls Panasonic Only Visible Traces Pot Test Controls Pot Test Results CommsMouse Point Values Send Direct Command Cam Comms Communications TestingAlarms MIC Comms SonySet Controls Get Preset from MICSend Preset to MIC Sony Set Clear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to File Table K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Learning a preset Help MIC412 Preset Codes for the Thermal Imager Bosch Protocol Aux Number Aux On Function Aux Off Function Go to a preset 36x optical zoom module MIC412TI and TF Dual Optical/Thermal PTZ Camera Connectivity Dimension Drawings Appendix a Sonyset Camera CommandsMIC 412 models Upright 90 Dimension Drawings Pelco Appendix B Protocol Preset Codes Washwipeonpreset Washwipeoffpreset Vision Special Setup Presets American Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-Pacific Bosch Security Systems, Inc