Important Safety Instructions | Bosch Appliances MIC412 manual

MIC412TI and MIC412TF Camera Installation and Operation Manual

EN 5

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions

2.Keep these instructions

3.Heed all warnings

4.Follow all instructions

5.Install according to manufacturer’s instructions

6.Do not install near any strong heat sources such as furnaces

7.Do not open the camera unit, doing so invalidates the unit’s warranty

8.Do not back-drive the pan or tilt axis of the camera. To do so will damage the motor drive gear chain and will invalidate the warranty

9.Do not use caustic or abrasive cleaning products on the unit

10.Do not point the MIC412 camera at the sun. Bosch Security Systems Ltd will not be liable for any damages to cameras which have been directly pointed at the sun

11.In situations where there could be a risk of injury should any part of the assembly become detached for any reason and fall, normal common sense safety precautions should be employed; a strong safety chain between the camera pan shaft and the mounting surface is recommended

12.For transportation please rotate the ball so the window points towards the base, this helps to protect the wiper & windows during transit

13.Ensure that the product case is properly earthed. If the product is likely to be struck by lightning, ensure that earth-bonding connections are made correctly to the mounting base of the unit

14.Use only the power sources indicated in this user guide and ensure that the current rating of the supply cable is adequate for the product

15.Do not stand canted (45°) MIC412’s upright as they can be easily knocked over, lay them on their side.

Bosch Security Systems

Issue 8

Image 5

Bosch Appliances MIC412 operation manual Important Safety Instructions

Contents

MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Appendices Glossary of Terms Introduction MIC412 Camera Versions MIC 412 Power Supply Unit Versions and Options Packaging Contents FeaturesMIC 412 Options Wiper Installation Environment Bosch Security Systems Issue Key to MIC-PMB drawing Associated Equipment and Typical Installations Installation Instructions Hardware Installation Electrical Connections Earthing of the MIC 412 cameraLightning Protection Power Supply Layout and Connections MIC 412TI and MIC 412TF Power Supply UnitsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth Link Table D -Telemetry Connections to HD3, HD4 and HD5 HD3 Terminal Box ID Marking Fuse Fuse function Terminal Box ConnectorRating for 240v Primary Rating for 115v Primary Commissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the Greenwich Adaptor Connecting the MIC 412 to the PCTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor Camset Tabs Wire RS485 Wire RS422 Table I Camera Interface Control Settings DIP SwitchConnecting the MIC-USB485CVTR, USB to RS485 Converter HD4 or HD5 MIC-USB485CVTR and Universal Camset Software Installation MIC Settings Boot MessagesCommissioning the MIC412 through Universal Camset Standard Controls Camset Settings Manual Control Pan, Tilt and Zoom Controls Iris Controls Preset PositionsFocus Controls Auxiliaries Pattern Tours Preset ToursTour Controls Soft Stops and Non Dwell Zones MIC SetupsNon-Dwell Zone Clear General Settings Other controls Auto Home Controls Default Settings Learn Alarm Positions Multi Alarm SettingsFrame Integration Settings Relay State, Activation and Re-arm Privacy Controls Privacy and Captions Privacy Calibration Captions Thermal FFC Mode and SettingsShutter Open/Close Gain and Auto Gain Modes Temperature and Humidity Advanced SettingsTimers Clear All Statistics Only Eeprom CopierDownload Eeprom To File Upload Eeprom From File POT Test Manual and Preset / Goto ControlsMenu Controls Panasonic Only Matrix Controls Visible Traces Pot Test Controls Mouse Point Values CommsPot Test Results Send Direct Command Alarms Communications TestingMIC Comms Cam Comms Send Preset to MIC Get Preset from MICSony Set SonySet Controls Load Table from File to MIC Execute this PresetSave Table from MIC to File Clear Table Table K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Learning a preset Help MIC412 Preset Codes for the Thermal Imager Bosch Protocol Aux Number Aux On Function Aux Off Function Go to a preset 36x optical zoom module MIC412TI and TF Dual Optical/Thermal PTZ Camera Connectivity MIC 412 models Upright 90 Dimension Drawings Appendix a Sonyset Camera CommandsDimension Drawings Pelco Appendix B Protocol Preset Codes Washwipeonpreset Washwipeoffpreset Vision Special Setup Presets American Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Europe, Middle East, Africa Contact AmericasAsia-Pacific Bosch Security Systems Inc Bosch Security Systems, Inc