Safety Precautions | Bosch Appliances MIC412 guide

MIC412TI and MIC412TF Camera Installation and Operation Manual

Safety Precautions

The following symbols are used throughout this manual please pay careful attention to their meaning.

The lightning flash with an arrowhead symbol within a triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important safety, operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safety Instructions

CAUTION

TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DISCONNECT POWER SUPPLY BEFORE OPENING THE

POWER SUPPLY UNIT.

POWER DISCONNECT: POWER SUPPLY UNITS HAVE

POWER SUPPLIED WHENEVER THE POWER CORD IS

INSERTED INTO THE POWER SOURCE.

WARNING

INSTALLATION SHOULD BE CARRIED OUT BY QUALIFIED

PERSONNEL IN ACCORDANCE WITH THE NATIONAL

ELECTRIC CODE, ANSI/NFPA, CANADIAN ELECTRICAL

CODE, AND ALL LOCAL COUNTRY CODES.

BOSCH SECURITY SYSTEMS ACCEPTS NO LIABILITY

FOR ANY DAMAGES OR LOSSES CAUSED DUE TO

INCORRECT OR IMPROPER INSTALLATION.

EN 4

WARNING

INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70 (FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN APPLICATION) AND IN ACCORDANCE TO LOCAL COUNTRY CODES FOR ALL OTHER COUNTRIES.

BRANCH CIRCUIT PROTECTION INCORPORATING A 20 A, 2-POLE LISTED CIRCUIT BREAKER OR BRANCH RATED FUSES ARE REQUIRED AS PART OF THE BUILDING INSTALLATION.

AREADILY ACCESSIBLE 2-POLE DISCONNECT DEVICE WITH A CONTACT SEPARATION OF AT LEAST 3 mm

MUST BE INCORPORATED.

ROUTING OF EXTERNAL WIRING MUST BE DONE THROUGH A PERMANENTLY EARTHED METAL CONDUIT.

WARNING

THE CAMERA MUST BE MOUNTED DIRECTLY AND PERMANENTLY TO A NON-COMBUSTIBLE SURFACE.

Bosch Security Systems

Issue 8

Image 4

Bosch Appliances MIC412 operation manual Safety Precautions

Contents

MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Terms Glossary of Appendices Introduction MIC 412 Power Supply Unit Versions and Options MIC412 Camera Versions Features Packaging ContentsMIC 412 Options Wiper Installation Environment Bosch Security Systems Issue Associated Equipment and Typical Installations Key to MIC-PMB drawing Hardware Installation Installation Instructions Lightning Protection Earthing of the MIC 412 cameraElectrical Connections MIC 412TI and MIC 412TF Power Supply Units Power Supply Layout and ConnectionsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth Link HD3 Table D -Telemetry Connections to HD3, HD4 and HD5 Terminal Box Connector Terminal Box ID Marking Fuse Fuse functionRating for 240v Primary Rating for 115v Primary Commissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the MIC 412 to the PC Connecting the Greenwich AdaptorTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor Connecting the MIC-USB485CVTR, USB to RS485 Converter Table I Camera Interface Control Settings DIP SwitchCamset Tabs Wire RS485 Wire RS422 MIC-USB485CVTR and Universal Camset Software Installation HD4 or HD5 Boot Messages MIC SettingsCommissioning the MIC412 through Universal Camset Standard Controls Camset Settings Manual Control Pan, Tilt and Zoom Controls Preset Positions Iris ControlsFocus Controls Auxiliaries Tour Controls Preset ToursPattern Tours MIC Setups Soft Stops and Non Dwell ZonesNon-Dwell Zone Clear General Settings Auto Home Controls Other controls Default Settings Multi Alarm Settings Learn Alarm PositionsFrame Integration Settings Relay State, Activation and Re-arm Privacy and Captions Privacy Controls Privacy Calibration Captions FFC Mode and Settings ThermalShutter Open/Close Gain and Auto Gain Modes Advanced Settings Temperature and HumidityTimers Clear All Statistics Eeprom Copier OnlyDownload Eeprom To File Upload Eeprom From File Manual and Preset / Goto Controls POT TestMenu Controls Panasonic Only Matrix Controls Pot Test Controls Visible Traces Pot Test Results CommsMouse Point Values Send Direct Command Communications Testing AlarmsMIC Comms Cam Comms Get Preset from MIC Send Preset to MICSony Set SonySet Controls Execute this Preset Load Table from File to MICSave Table from MIC to File Clear Table Table K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Help MIC412 Preset Codes for the Thermal Imager Learning a preset Go to a preset Bosch Protocol Aux Number Aux On Function Aux Off Function MIC412TI and TF Dual Optical/Thermal PTZ Camera 36x optical zoom module Connectivity Dimension Drawings Appendix a Sonyset Camera CommandsMIC 412 models Upright 90 Dimension Drawings Appendix B Protocol Preset Codes Pelco Washwipeonpreset Washwipeoffpreset Special Setup Presets Vision American Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Contact Americas Europe, Middle East, AfricaAsia-Pacific Bosch Security Systems Inc Bosch Security Systems, Inc