Sony Set, SonySet Controls | Bosch Appliances MIC412 guide

MIC412TI and MIC412TF Camera Installation and Operation Manual		EN 44
Sony Set	SonySet Controls

SonySet Prest Number

This is where the SonySet Preset number is selected, there are 10 options available relating to 10 complete camera setups.

The Sonyset tab shows the controls required for Creating, Loading, Saving, Uploading and Downloading SonySet tables in FV protocol only.

A MIC can store 10 Sony Set tables, each containing 10 separate camera controls.

This means that a complete setup for the camera module (shutter speed, gain level, effect etc) can be saved and loaded back at any time through an input from the user. These can therefore be used to define certain camera states for different positions or requirements of an installation, for example, one could be set up for normal running auto everything, and another set-up for ANPR, with a specified frame rate and gain etc.

These states could then be toggled by calling them up with an Execute SonySet command.

Get Preset from MIC

This process will query the MIC for the table number as specified in the SonySet Preset Number list. Each valid command and value will be shown in the table. If any data is incorrect or the command does not exist the Sony Command column will display "Invalid". It is not advised to reprogram a MIC with any "Invalid" commands.

Send Preset to MIC

This will read through the entire table checking for valid commands and respective values indicating any discrepancies, and then form the commands to send the data to the MIC. The data is stored to the preset number as indicated in the SonySet Preset Number in list.

Bosch Security Systems

Issue 8

Image 44

Bosch Appliances MIC412 Sony Set, SonySet Controls, SonySet Prest Number, Get Preset from MIC, Send Preset to MIC

Contents

MIC412 Dual Optical / Thermal PTZ Camera MIC 412 Dual Optical / Thermal PTZ Camera Power Supply Installation and Camera Setup… Safety Precautions Important Safety Instructions Glossary of Terms Glossary of Appendices Introduction MIC 412 Power Supply Unit Versions and Options MIC412 Camera Versions Features Packaging ContentsMIC 412 Options Wiper Installation Environment Bosch Security Systems Issue Associated Equipment and Typical Installations Key to MIC-PMB drawing Hardware Installation Installation Instructions Electrical Connections Earthing of the MIC 412 cameraLightning Protection MIC 412TI and MIC 412TF Power Supply Units Power Supply Layout and ConnectionsMIC-24PSU-UL, MIC-115PSU-UL, and MIC-240PSU-UL PCB Earth Link HD3 Table D -Telemetry Connections to HD3, HD4 and HD5 Terminal Box Connector Terminal Box ID Marking Fuse Fuse functionRating for 240v Primary Rating for 115v Primary Commissioning the MIC 412 with heater option fitted Fitting the optional Sunshield Connecting the MIC 412 to the PC Connecting the Greenwich AdaptorTable G Connecting the Greenwich Adaptor Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor Camset Tabs Wire RS485 Wire RS422 Table I Camera Interface Control Settings DIP SwitchConnecting the MIC-USB485CVTR, USB to RS485 Converter MIC-USB485CVTR and Universal Camset Software Installation HD4 or HD5 Boot Messages MIC SettingsCommissioning the MIC412 through Universal Camset Standard Controls Camset Settings Manual Control Pan, Tilt and Zoom Controls Preset Positions Iris ControlsFocus Controls Auxiliaries Pattern Tours Preset ToursTour Controls MIC Setups Soft Stops and Non Dwell ZonesNon-Dwell Zone Clear General Settings Auto Home Controls Other controls Default Settings Multi Alarm Settings Learn Alarm PositionsFrame Integration Settings Relay State, Activation and Re-arm Privacy and Captions Privacy Controls Privacy Calibration Captions FFC Mode and Settings ThermalShutter Open/Close Gain and Auto Gain Modes Advanced Settings Temperature and HumidityTimers Clear All Statistics Eeprom Copier OnlyDownload Eeprom To File Upload Eeprom From File Manual and Preset / Goto Controls POT TestMenu Controls Panasonic Only Matrix Controls Pot Test Controls Visible Traces Mouse Point Values CommsPot Test Results Send Direct Command Communications Testing AlarmsMIC Comms Cam Comms Get Preset from MIC Send Preset to MICSony Set SonySet Controls Execute this Preset Load Table from File to MICSave Table from MIC to File Clear Table Table K Sonyset Commands Value MIC Programmer Bosch Security Systems Issue Help MIC412 Preset Codes for the Thermal Imager Learning a preset Go to a preset Bosch Protocol Aux Number Aux On Function Aux Off Function MIC412TI and TF Dual Optical/Thermal PTZ Camera 36x optical zoom module Connectivity MIC 412 models Upright 90 Dimension Drawings Appendix a Sonyset Camera CommandsDimension Drawings Appendix B Protocol Preset Codes Pelco Washwipeonpreset Washwipeoffpreset Special Setup Presets Vision American Dynamics Special Setup Presets Kalatel Molynx Autoironpreset Autoiroffpreset Multialarmonpreset Panasonic Bosch Forward Vision Intermitantwipeonpreset Intermitantwipeoffpreset VCL Vicon Rightpreset Softlimitbottom Multialarmpreset Contact Americas Europe, Middle East, AfricaAsia-Pacific Bosch Security Systems Inc Bosch Security Systems, Inc