FCC & Ices compliance | Bosch Appliances VEZ-400 manual

10 en Safety	VEZ-400 Mini PTZ Dome

SELV - All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits.

Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the Telephone Network Voltage (TNV) circuits.

The system ground is only used to comply with safety standards or installation practices in certain countries. Bosch does not recommend connecting system ground to safety ground unless it is explicitly required. However, if the system ground and safety ground are connected and grounding loops are causing interference in the video signal, use an isolation transformer (available separately from Bosch).

CAUTION!

Connecting System ground to Safety ground may result in ground loops that can disrupt the CCTV system.

Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.

1.4FCC & ICES compliance

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

–this device may not cause harmful interference, and

–this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules and ICES-003of Industry Canada. These limits are designed to provide reasonable protection against harmful

F.01U.252.635 2.0 2011.09

User Manual

Bosch Security Systems, Inc.

Image 10

Bosch Appliances VEZ-400 user manual FCC & Ices compliance, FCC & Ices Information

Contents

VEZ-400 Mini PTZ Dome Page Table of Contents WDR/DNR Safety Safety precautions Important safety instructions Important notices Coax grounding Rack mount FCC & Ices compliance FCC & Ices Information Informations FCC et Ices Modèles utilisés aux États-Unis et au Canada uniquement En Safety VEZ-400 Mini PTZ Dome Bosch notices Disclaimer Trademarks CopyrightMore information Features Description Unpacking Parts ListQty Description Additional Tools Required AccessoriesModel Number Description Drawing Installation Overview Installing a Surface Mount Number Description En Installing a Surface Mount VEZ-400 Mini PTZ Dome VEZ-400 Mini PTZ Dome Installing a Surface Mount en Connection Typical wiring configuration RS-485 Connections Number Signal Color TRX Video Connection Alarm ConnectionsAWG Camera Settings Power Connections16AWG SW301 Rotary switch SW303 Dip switches SW302 Rotary switch No1 No2 Protocol Setting the address ID of the cameraSetting the protocol of the camera No3 No4 Baud Rate bps VEZ-400 Mini PTZ Dome On-Screen Display OSD MenuBasic Navigation and Common Actions CAM Test ...PASS Command Action KEY Main Menu System SetupMain Menu Main Menu Choices Description Menu Description Editing TitlesTitle Clearing Saved Functions System Setup MenuSystem Setup System Information Initialize RebootReboot System Information ALL CAM Preset Tour Pattern Scan ETC Save Back PasswordInitialize Password Display SetupOSD Setup Display Setup OSD Setup Privacy Zone Privacy Zone Setup Select Privacy ZONE. The screen Privacy Zone Setup appearsPRIVACY.## Edit Display Width Height Clear Save Back Change Motion/Face Detection Image SetupImage Setup Mirror Save Back MOTION/FACE Detection MD/FD Sensitivity Alarm Atime Save BackLanguage OSD Select FOCUS/ZOOM. The screen FOCUS/ZOOM Setup appears Camera SetupCamera Setup Focus/Zoom FOCUS/ZOOM Setup WB SetupFocus Zoom SPD Save Back WB Setup AE SetupMode Gain B Gain Save Back Mode Shut AGC Gain AGC MAX DSS Bright Save Back 4 D/N SetupAE Setup AE Mode Full Auto Manual Advanced SetupDAY/NIGHT Detect Dtime Save Back 6 WDR/DNR Select ADVANCED. The screen Advanced Setup appearsAdvanced Setup Sharpness Backlight Save Dome Motion Setup Dome Motion SetupWDR Setup WDR Level DNR Setup DNR Level Save Back General Setup Motion Setup Home Action Calibration Exit Select General SETUP. The screen General Setup appears General SetupMotion Setup General Setup Home Action Select Motion SETUP. The screen Motion Setup appearsMotion Setup Prop PAN/TILT Auto Flip Over Tilt Save Back Home Action Setup Select Home ACTION. The screen Home Action Setup appearsAction Number Time Mode Save Back Auto CAL Error MSG Disp Calibration Save Back Select CALIBRATION. The screen Calibration Setup appearsCalibration Setup Calibration Preset Setup Preset SetupEdit Title Time Clear Save Back Pattern Setup Pattern Setup Tour Setup Tour SetupTOUR1 Preset only Save Back Change ID Change ACT Clear ID Scan Setup Scan SetupEdit Speed Dtime Direction Mode Clear Save Back Alarm Setup Alarm SetupOUT Priority Action Number Atime Save Back SET/CLEAR Troubleshooting Problem Solution VEZ-400 Mini PTZ Dome Troubleshooting en WDR Technical SpecificationsCamera Module DNR Mechanical NC/NOEnvironment Dimensions Dimensions Camera Preset Key Example Number Bosch Protocol En Bosch Protocol VEZ-400 Mini PTZ Dome Preset Key Operation Example Number Pelco Protocol En Pelco Protocol VEZ-400 Mini PTZ Dome Page Bosch Security Systems, Inc